Filtres
Allows installation wheels with larger center bore to the existing bore diameter Made of plastic Has a positive effect on the suspension Dimensions: Center bore in wheel: 106 mm Bore diameter in hub: 77,8 mm In the box: (4) Hub ring
Kit Demi-lames Additionnelles IRONMAN 4X4 Load Plus LP4 +450kg • 70x12x442mm • Système breveté qui permet de rouler jusu'à la charge maximum autorisée en toute sécurité • S'installe et se dépose en 20 minutes seulement à l'aide de 2 clés plates • Idéal pour les configurations charges lourdes occasionnelles ou permanentes
Kit Demi-lames Additionnelles IRONMAN 4X4 Load Plus LP7 +450kg • 75x12x438mm • Système breveté qui permet de rouler jusu'à la charge maximum autorisée en toute sécurité • S'installe et se dépose en 20 minutes seulement à l'aide de 2 clés plates • Idéal pour les configurations charges lourdes occasionnelles ou permanentes
Increased ground clearance Levels the front with the rear of the vehicle Gives an aggresive look Lift kit consists of: Front crossmember Front brake lines Front brake line brackets Front differential skid plate Break line drop brackets Steering knuckle Tie rod end Differential bracket mounting Driveshaft spacer Sway bar drop brackets Sway bar end link Rear crossmember Rear track bar bracket Bump stop extensions Upper control arms relocation brackets Strut spacers (2) FOX shocks Note: Cutting required Does NOT fit diesel models For models with LARGE hub bore ONLY Fits factory Air Ride equipped trucks only The factory Air Ride is a closed loop system. Opening the system more times than recommended in the lift instructions will require the system to be recharged. This can be done at any Ram dealer service department. A scan tool is needed to access the air control module to perform the service Frame bracket modification required Fits 4WD models equipped with factory air ride only. Stock 17" and 18" wheels cannot be re-installed, stock 20" wheels can only be re-installed with factory tire size If truck is equipped with standard hub bore use lift with standard steering knuckles BDS1697H (NX2 shocks) or BDS1697FS (FOX shocks), kits sold separately
Increased ground clearance Levels the front with the rear of the vehicle Gives an aggresive look Lift kit consists of: Front crossmember Front brake lines Front brake line brackets Front differential skid plate Break line drop brackets Steering knuckle Tie rod end Differential bracket mounting Driveshaft spacer Sway bar drop brackets Sway bar end link Rear crossmember Rear track bar bracket Bump stop extensions Upper control arms relocation brackets Strut spacers (2) NX2 shocks Note: Cutting required Does NOT fit diesel models For models with LARGE hub bore ONLY Fits factory Air Ride equipped trucks only Fits 4WD models equipped with factory air ride only. The factory Air Ride is a closed loop system. Opening the system more times than recommended in the lift instructions will require the system to be recharged. This can be done at any Ram dealer service department. A scan tool is needed to access the air control module to perform the service Frame bracket modification required Stock 17" and 18" wheels cannot be re-installed, stock 20" wheels can only be re-installed with factory tire size If truck is equipped with standard hub bore use lift with standard steering knuckles BDS1697H (NX2 shocks) or BDS1697FS (FOX shocks), kits sold separately,
Increased ground clearance Levels the front with the rear of the vehicle Clears up to 35" tires Gives an aggresive look Lift kit consists of: Front crossmember Front brake lines Front brake line brackets Front differential skid plate Break line drop brackets Steering knuckle Tie rod end Differential bracket mounting Driveshaft spacer Sway bar drop brackets Sway bar end link Rear crossmember Rear track bar bracket Bump stop extensions Upper control arms relocation brackets Strut spacers (2) BDS NX2 Nitro series shocks Note: Cutting required Does NOT fit diesel models For models with STANDARD hub bore ONLY Fits factory Air Ride equipped trucks only Fits 4WD models equipped with factory air ride only. Extreme care/caution must be taken to follow the steps of instructions or damage to the bags during installation. The factory Air Ride is a closed loop system. Opening the system more times than recommended in the lift instructions will require the system to be recharged. This can be done at any Ram dealer service department. A scan tool is needed to access the air control module to perform the service Frame bracket modification required Stock 17" and 18" wheels cannot be re-installed, stock 20" wheels can only be re-installed with factory tire size If truck is equipped with factory 22" wheels use the "large hub bore" steering knuckles lift BDS1642H (NX2 shocks) or BDS1642FS (FOX shocks), kits sold separately
Increased ground clearance Levels the front with the rear of the vehicle Clears up to 35" tires Gives an aggresive look Lift kit consists of: Front crossmember Front brake lines Front brake line brackets Front differential skid plate Break line drop brackets Steering knuckle Tie rod end Differential bracket mounting Driveshaft spacer Sway bar drop brackets Sway bar end link Rear crossmember Rear track bar bracket Bump stop extensions Upper control arms relocation brackets Strut spacers (2) Fox Performance Series 2.0 IFP shocks Note: Cutting required Does NOT fit diesel models For models with STANDARD hub bore ONLY Fits factory Air Ride equipped trucks only Fits 4WD models equipped with factory air ride only. Extreme care/caution must be taken to follow the steps of instructions or damage to the bags during installation. The factory Air Ride is a closed loop system. Opening the system more times than recommended in the lift instructions will require the system to be recharged. This can be done at any Ram dealer service department. A scan tool is needed to access the air control module to perform the service Frame bracket modification required Stock 17" and 18" wheels cannot be re-installed, stock 20" wheels can only be re-installed with factory tire size If truck is equipped with factory 22" wheels use the "large hub bore" steering knuckles lift BDS1698H (NX2 shocks) or BDS1698FS (FOX shocks), kits sold separately
FOX 2.5 Performance Elite coil-overs offer improved damper performance over stock DSC controller allows easy adjustment of LSC and HSC compression for performance on any terrain Performance UCAs increase strength and allow for more suspension travel FOX 2.0 performance series IFP rear shocks Increased strength and suspension travel Easy bolt on installation In the box: (2) Front upper control arm (2) Front Coil-Over Performance Elite 2.5 Reservoir adjustable DSC (2) Rear Shock 2.0 Performance IFP (2) Rear spring Notes: Will not fit models with stock pneumatic suspension Will not work with stock rims with a 12.50" wide tire If the stock rim is reinstalled it will need to be fitted with the stock-size tire ONLY Vehicles equipped with Offroad or Rebel Package will not achieve the full 3" of lift, net ride height change will be around 2" above stock
Increased ground clearance Levels the front with the rear of the vehicle Gives an aggresive look Lift kit consists of: Front cross-members Front brake line Front brake line brackets Front steering knuckle Tie rod end Differential bracket mounting Driveshaft spacer Sway bar drop brackets Skid plate Strut spacers Rear cross-members (2) FOX Nitro series shocks Notes: Cutting required Doest NOT fit diesel models Will NOT fit adjustable air suspension equipped models Fits ONLY vehicles with LARGE hub bore Stock 17" wheels cannot be reinstalled to to steering interference. Stock 20s can be reinstalled with factory tire size If truck is equipped with STANDARD hub bore use lift with standard steering knuckles BDS1663H (NX2 shocks) or BDS1663FS (FOX shocks), kit sold separately
Increased ground clearance Levels the front with the rear of the vehicle Gives an aggresive look Lift kit consists of: Front cross-members Front brake line Front brake line brackets Front steering knuckle Tie rod end Differential bracket mounting Driveshaft spacer Sway bar drop brackets Skid plate Strut spacers Rear cross-members (2) BDS NX2 Nitro series shocks Notes: Cutting required Doest NOT fit diesel models Will NOT fit adjustable air ride models Fits ONLY vehicles with LARGE hub bore Stock 17" wheels cannot be reinstalled to to steering interference. Stock 20s can be reinstalled with factory tire size For models with STANDARD bore You must to buy lift kit BDS1663FS (with Fox shocks) or lift kit BDS1663H (with NX2 shocks), sold separately
Levels the front with the rear of the vehicle Increased ground clearance Corrects suspension, steering, & driveline geometry Lift consists of: Front Crossmember Front Brake Line Front Brake Line Brackes Front Steering Knuckles Tie Rod End w/Nut Skid Plate Differential drop brackets Sway bar drop brackets Drive Shaft Spacer Rear Crossmember Bump stop extension Relocation brackets Sway bar links Coil spring (2) shocks BDS NX2 Notes: Cutting required Does NOT fit diesel models Fits ONLY vehicles with LARGE hub bore Will NOT fit adjustable air suspension equipped models RAMs with factory 22" wheels require the larger bore knuckles due to larger wheel bearing assembly. Reference build code WPM or WPZ. Stock 17" wheels cannot be reinstalled to to steering interference. Stock 20s can be reinstalled with factory tire size This system will NOT fit vehicles equipped with STANDARD hub bore If truck is equipped with STANDARD hub bore use lift with standard steering knuckles BDS1661H (NX2 shocks) or BDS1661F (FOX shocks), kit sold separately
Increased ground clearance Levels the front with the rear of the vehicle Gives an aggresive look In the box: Front cross-members Front brake line Front brake line brackets Front steering knuckle Tie rod end Differential bracket mounting Driveshaft spacer Sway bar drop brackets Skid plate Strut spacers Rear cross-members (2) BDS NX2 Nitro series shocks Notes: Cutting required Fits ONLY vehicles with STANDARD hub bore This kit will NOT work on Diesel models. RAMs with factory 22" wheels require the larger bore knuckles due to larger wheel bearing assembly. Reference build code WPM or WPZ Will NOT fit adjustable "air ride" suspension equipped models Stock 17" wheels cannot be reinstalled to to steering interference. Stock 20s can be reinstalled with factory tire size For models with large bore You must to buy lift kit BDS1664FS (with Fox shocks) or lift kit BDS1664H (with NX2 shocks), sold separately
Levels the front with the rear of the vehicle Increased ground clearance Corrects suspension, steering, & driveline geometry Lift consists of: Front Crossmember Front Brake Line Front Brake Line Brackes Front Steering Knuckles Tie Rod End w/Nut Skid Plate Differential drop brackets Sway bar drop brackets Drive Shaft Spacer Rear Crossmember Bump stop extension Relocation brackets Sway bar links Coil spring (2) shocks BDS NX2 Notes: Cutting required Fits ONLY vehicles with STANDARD hub bore RAMs with factory 22" wheels require the larger bore knuckles due to larger wheel bearing assembly. Reference build code WPM or WPZ Will NOT fit adjustable "air ride" suspension equipped models If installing the 6" kit on a Rebel or truck equipped with. an "off road group package" the truck will sit roughly 1/2" front high with the preload spacer installed. If the preload spacer isn't installed the truck will sit about 3/8" now low. Stock 17" wheels cannot be reinstalled to to steering interference. Stock 20s can be reinstalled with factory tire size This kit will NOT work on Diesel models. If truck is equipped with LARGE hub bore use lift with standard steering knuckles BDS1662H (NX2 shocks) or BDS1662F (FOX shocks), kit sold separately If installing the 6" kit on a Rebel or truck equipped with. an “off road group package” the truck will sit roughly 1/2" front high with the preload spacer installed. If the preload spacer isn’t installed the truck will sit about 3/8" front low. Neither will have a level stance.
Increased ground clearance Levels the front with the rear of the vehicle Gives an aggresive look Lift consists of: Front Crossmember Front Brake Line Front Brake Line Brackes Front Steering Knuckles Tie Rod End w/Nut Skid Plate Differential drop brackets Sway bar drop brackets Drive Shaft Spacer Rear Crossmember Bump stop extension Relocation brackets Strut spacer box kit (2) Rear shocks Fox Performance 2.0 IFP Notes: Cutting required Fits ONLY vehicles with STANDARD hub bore RAMs with factory 22" wheels require the larger bore knuckles due to larger wheel bearing assembly. Reference build code WPM or WPZ Will NOT fit adjustable "air ride" suspension equipped models Will NOT fit 2019 RAM 1500 Classic models, Refer to the 2018 kit listings Stock 17" wheels cannot be reinstalled to to steering interference. Stock 20s can be reinstalled with factory tire size This kit will NOT work on Diesel models. For models with large bore You must to buy lift kit BDS1664FS (with Fox shocks) or lift kit BDS1664H (with NX2 shocks), sold separately
FOX
Proudly made in the USA Easy bolt-on installation No cutting or drilling required Increased ground clearance Levels the front and rear of the truck Control arms include POM ball joints for greater range of motion and easier installation Ball joints are pre-installed to ease installation In the box: Front forged aluminium upper control arms Front strut spacers Front preload strut spacers Rear coil spacers (2) Rear N3 Premium shocks Hardware Notes: Does NOT fit "TRX" models Does NOT fit models with factory air ride suspension
Easy Bolt-On installation No Cutting or Drilling required! Includes New forged aluminum upper control arms Control arms include POM ball joints for greater range of motion and easier installation Ball joints are pre-installed to ease installation Increased ground clearance Levels the front and rear of the truck Can be returned to stock Fits Rebel Models Strut specs: Easy bolt-on installation Includes pre-loaded coil for no-fuss installation Maintains smooth, factory-like ride Increased ground clearance Application specific velocity sensitive valving Structurally engineered for lifted applications Nitrogen gas charged to improve ride, handling, and reduce shock oil aeration Offers improved tire contact with the road for increased stability and performance Infinitely Variable Damping Leak-proof piston seal Special formulated low friction shock oil Massive 1 3/8in Bore Hardened chromed piston rod provides superior corrosion resistance and enhances sealing properties Silver powder coat finish In the box: (2) Strut N3 Premium (2) Forged aluminum upper control arm (2) Strut preload spacer (2) Strut spacer (2) Coil spacer (2) Shock N3 Premium Hardware Notes: Fits 4WD models ONLY Does NOT fit "TRX" models Does NOT fit models with factory air ride suspension
Proudly made in the USA Increased ground clearance Levels front of vehicle with rear Maintains factory air ride modes In the box: Front lifted knuckles Front strut spacers Front crossmember Front differential drop brackets Front driveshaft spacer Front sway-bar links Front skid plate Rear coil spacers Rear crossmember Rear sway-bar links Rear track bar bracket Rear bump stop extensions Rear brake line brackets Rear brake lines (2) Rear Premium N3 series shocks Hardware Notes: Cutting required Fits models with 22XL (large center bore) rims ONLY, check the sticker on the door If you don't have the 22XL model, the appropriate lift is under the RCK33830A index Fits models with factory air ride suspension ONLY Does NOT fit 2019 "classic" models (5-lug) Kit is not recommended for AWD models,"TRX" models will achieve approximately 1" of additional lift Requires 20" or larger wheels Does NOT fit 18" or smaller wheels Fits 4WD models ONLY
Proudly made in the USA Increased ground clearance Levels the front with the rear of the vehicle Front strut specs: Easy bolt-on installation Includes pre-loaded coil for no-fuss installation Maintains smooth, factory-like ride Increased ground clearance Application specific velocity sensitive valving Structurally engineered for lifted applications Nitrogen gas charged to improve ride, handling, and reduce shock oil aeration Offers improved tire contact with the road for increased stability and performance Infinitely Variable Damping Leak-proof piston seal Special formulated low friction shock oil Massive 1 3/8in Bore Hardened chromed piston rod provides superior corrosion resistance and enhances sealing properties Silver powder coat finish In the box: (2) Front strut N3 Premium Front lifted knuckles Front strut spacers Front crossmember Front differential drop brackets Front driveshaft spacer Front sway-bar drop brackets Front skid plate Rear variable rate coils Rear coil spacers Rear crossmember Rear sway-bar links Rear track bar bracket Rear bump-stop extensions Rear brake line brackets Hardware (2) Rear shock N3 Premium Notes: Fits models with 22XL rims ONLY. If you dont have the 22XL model, the appropriate lift is under the RCK33430A index (sold separately) Fits Rebel Models Fits 4WD models ONLY Does NOT fit models with factory air ride suspension Does NOT fit 2019 "classic" models (5-lug) "TRX" models will achieve approximately 1" of additional lift This lift is not recommended for use on the TRX models due to possible CV shaft vibration caused by the additional lift
Proudly made in the USA Increased ground clearance Levels the front with the rear of the vehicle Allows for the assembly 37" wheels In the box: Front lifted knuckles Front strut spacer Front crossmember Front differential drop brackets Front driveshaft spacer Front skid plate Front sway-bar drop brackets Rear coil spacers Rear crossmember Rear sway-bar links Rear track bar bracket Rear bump-stop extensions Rear brake line brackets (2) Rear Premium N3 series Hardware Notes: Cutting required Fits models with 22XL rims ONLY, check the sticker on the door. If you don't have the 22XL model, the appropriate lift is under the RCK33430A index Does NOT fit models with factory air ride suspension Does NOT fit Rebel models Kit is not recommended for AWD models "TRX" models will achieve approximately 1" of additional lift. This lift is not recommended for use on the TRX models due to possible CV shaft vibration caused by the additional lift Requires 20" or larger wheels Does NOT fit 18" or smaller wheels Fits 4WD models ONLY
Proudly made in the USA Increased ground clearance Levels front of vehicle with rear Maintains factory air ride modes In the box: Front lifted knuckles Front strut spacers Front crossmember Front differential drop brackets Front driveshaft spacer Front sway-bar links Front skid plate Rear coil spacers Rear crossmember Rear sway-bar links Rear track bar bracket Rear bump stop extensions Rear brake line brackets Rear brake lines (2) Rear Premium N3 series shocks Hardware Notes: Cutting required Does NOT fit models with 22XL rims, check the sticker on the door If you have the 22XL model, the appropriate lift is under the RCK34430A index Fits models with factory air ride suspension ONLY Does NOT fit 2019 "classic" models (5-lug) Kit is not recommended for AWD models,"TRX" models will achieve approximately 1" of additional lift Requires 20" or larger wheels Does NOT fit 18" or smaller wheels Fits 4WD ONLYmodels
Proudly made in the USA Increased ground clearance Levels the front with the rear of the vehicle Allows for the assembly 37" wheels In the box: Front lifted knuckles Front strut spacer Front crossmember Front differential drop brackets Front driveshaft spacer Front skid plate Front sway-bar drop brackets Rear coil spacers Rear crossmember Rear sway-bar links Rear track bar bracket Rear bump-stop extensions Rear brake line brackets (2) Rear Premium N3 series Hardware Notes: Fits 4WD models ONLY Fits Rebel models Cutting required Does NOT fit models with 22XL rims, check the sticker on the door. If you have the 22XL model, the appropriate lift is under the RCK33930A index Does NOT fit models with factory air ride suspension Kit is not recommended for AWD models "TRX" models will achieve approximately 1" of additional lift. This lift is not recommended for use on the TRX models due to possible CV shaft vibration caused by the additional lift Requires 20" or larger wheels Does NOT fit 18" or smaller wheels
Proudly made in the USA Increased ground clearance Levels the front with the rear of the vehicle Shock specs: 10-Stage variable valving High pressure nitrogen charged 35mm piston Chromed hardened 18mm piston rod 54mm Shock body to dissipate heat faster 36kN Tensile strength Spring loaded piston rod seal Military spec. fluid rated To –40° C Rubber bushings for better absorption Metallic silver paint In the box: (2) Front strut N3 Premium Front lifted knuckles Front strut spacers Front crossmember Front differential drop brackets Front driveshaft spacer Front sway-bar drop brackets Front skid plate Rear variable rate coils Rear coil spacers Rear crossmember Rear sway-bar links Rear track bar bracket Rear bump-stop extensions Rear brake line brackets Hardware (2) Rear shock N3 Premium Notes: Fits Rebel Models Fits 4WD models ONLY Requires 20" or larger wheels Does NOT fit 18" or smaller wheels Does NOT fit 22" factory wheels Does NOT fit models with factory air ride suspension Does NOT fit 2019 "classic" models (5-lug) "TRX" models will achieve approximately 1" of additional lift This lift is not recommended for use on the TRX models due to possible CV shaft vibration caused by the additional lift
ROUGH COUNTRY RC70779DRL • Kit barre LED 20" ROUGH COUNTRY 70779DRL pour intégration masquée derrière la calandre basse
Universal fit and bolt-on installation for all Element bumper applications Solid front cover panel protects light bar when not in use and opens up when needed Activated by switch inside cab Works with most 20" LED double row light bars Plug-and-play wire harness and toggle switch included
Aligns the front with the rear of the vehicle Increases ground clearance Preserves factory driving comfort Strut extensions made of high quality aluminium Easy to install In the box: (2) Strut extension Hardware Notes: Fits 4WD models ONLY Does NOT fit with Mega Cab models Does NOT fit models with Air Ride suspension Actual spacer thickness is not a 1 to 1 ratio with the gained lift due to the suspension geometry
Proudly made in the USA Easy bolt-on installation Increased ground clearance Levels the front with the rear of the vehicle Maintains factory ride quality and re-uses your factory coil spring In the box: (4) Front pre-load spacers (2) Front sensor brackets (2) Rear coil spring spacers (2) Rear sensor brackets Hardware Notes: Fits TRX models ONLY Fits 4WD models ONLY Does NOT fit models with factory air ride suspension Requires disassembling your strut to install
Proudly made in the USA Easy bolt-on installation Increased ground clearance Levels the front with the rear of the vehicle Maintains factory ride quality and re-uses your factory coil spring In the box: (2) Strut preload spacer Notes: Does NOT fit "TRX" models Does NOT fit models with factory air ride suspension Requires disassembling your strut to install Lifts front 2"
Proudly made in the USA Easy bolt-on installation Increased ground clearance Levels the front with the rear of the vehicle Maintains factory ride quality and re-use of factory air ride In the box: (2) Sensor relocation brackets Notes: Fits 4WD models ONLY Fits models with factory air ride suspension ONLY Does NOT fit Rebel models Will NOT be able to use Off Road Mode 1 and 2 due to new lift height
Front: 0-2,25" Rear: 0" Levels the front with the rear Front leveling monotube shocks w/ tuning optimized for on- and off-road driving Rear adjustable piggyback shocks w/ 3-postiion Fast Adjust Knob for large damping adjustments Rear settings include: Sport, Moderate Tow/Haul, Heavy Tow/Haul Ideal for daily driving, off-road excursions, and tow/haul duties as well as the serious enthusiast wanting a consistent, firm feel through all driving conditions In the box: Front Sport Leveling Monotube Shocks 0-2,25" Lift Front Microcellular Progressive Bump Stops Front Billet coil spring carriers Front Injection molded squeak-free spring isolator Rear Sport Tow/Haul Adjustable Piggyback Shocks 0" Lift Rear Microcellular Progressive Bump Stops Rear Roost guards Hardware Notes: Fit Rebel models Never exceed factory tow/haul ratings Does NOT fit Dodge/Ram trucks equipped w/ Active-Level Four-Corner Air Suspension Do not use tow/haul modes while unladen as the increased rear stiffness could upset the balance between the front and rear of the vehicle, which could lead to loss of vehicle control
Allows for the installation of: Above: LED light bar up to 20" single / double or 4 pieces of Cube LED light up to 3" Under: LED light bar up to 20" single / double or 4 pieces of Cube LED light up to 3" In the center single LED bar up to 10" Made from steel One piece design Texture black Mesh screen in light bar can be removed for installation of lights High-quality product No drilling required Notes: Lights sold separately Fits Go Rhino BR5.5/BR6 bumper ONLY
Made from steel Modular design Texture black No drilling required Allows to add LED lights 3" Sold in pairs Notes: Fit Surface mounted light options ONLY Fit to front bumpers BR5.5, BR5, BR6, BR10, BR10.5 i BR11 ONLY (sold separately) We recommend Rough Country 2" LED lights (can't be mounted with lights covers) (sold separately)
Made from steel Modular design Texture black No drilling required Sold in pairs Notes: Fit Go Rhino rear bumper BR20 ONLY We recommend Rough Country Flush Mount 2" LED lights
M14x1,5mm Color black Allows for proper wheels assembly Dimensions: Key length: 90 mm Nut height: 50 mm In the box: (24) Lug nut Lug nuts key Notes: If you don't know if the nuts will mach please contact our sales department Do NOT use with pneumatic wrench
High quality It allows you to manually raise or lower Weatherproof Logo AMP Research Notes: Running boards will return to Auto Operation in the next door cycle after 30 minutes Does NOT fit with PowerStep AMP Research AMP75141-01A, AMP75134-01A (sold separately)
Pack de protections inférieures RIVAL • DODGE RAM 1500 et 1500 TRX (2018+) • Véhicules sans suspension pneumatique
Pack de protections inférieures RIVAL • DODGE RAM 1500 5.7, 5.7 Hybrid (2018+) • Véhicules avec suspension pneumatique
Pack de protections inférieures RIVAL • DODGE RAM 1500 3.0D (2018+) • Véhicules avec suspension pneumatique
Pack de protections inférieures RIVAL • DODGE RAM 1500 3.0D (2018+) • Véhicules sans suspension pneumatique
Construction: Solid aluminum 6061-T6 Bolt Pattern: 6x139,7 mm Centre Bore: 77,8 mm Thickness: 38 mm Thread: M14x1,5 Increased rust resistance Black anodized finish Laser-engraved OFD logo In the box: (2) Wheel spacer (12) Lug nut Notes: Fit models with M14x1,5 nuts ONLY
Complete kit with bars and mounting brackets Easy installation, no drilling required Full length drop down step Great for accessing vehicles for lift kits and oversize tires Protects rocker panel from trail obstacles and road debris Provides sturdy full length step area for enhanced access Textured black powder coat finish Uses OEM step and rock rail mount locations In the box: (2) Side steps Hardware Notes: Fits Crew Cab models only
Black textured powder coat finish High quality Made of steel Durable, one-piece construction Dual purpose design and steel construction allows D6 to be used as a step and a rock slider Mounts tight to rocker panel for maximum ground clearance and protection Punched steel step plate area is 6" wide and has raised hex pattern to provide no-slip grip Makes it easier to get in and out of the vehicle, especially in vehicles with a suspension lift Easy to install In the box: (2) Side steps Dominator D6 Hardware Notes: Additional drop steps available GR69420000T (sold separately) Fit Crew Cab models ONLY
Black textured powder coat finish High quality Made of durable steel Robust and one-piece construction Protects rocker panel from trail obstacles and road debris Makes it easier to get in and out of the vehicle, especially in vehicles with a suspension lift Full length slider with outer rub rail and removable full length steel step Installation in the factory holes, no drilling required Could be mounted without mesh plate Easy to install In the box: (2) Side steps Dominator D1 (2) Mesh plate Hardware Notes: Complete kit with bars and mounting brackets Fits Quad Cab models only
Black textured powder coat finish High quality Made of durable steel Robust and one-piece construction Protects rocker panel from trail obstacles and road debris Makes it easier to get in and out of the vehicle, especially in vehicles with a suspension lift Full length slider with outer rub rail and removable full length steel step Installation in the factory holes, no drilling required Could be mounted without mesh plate Easy to install In the box: (2) Side steps Dominator D6 Hardware Notes: Optional bolt-on drop steps available (sold separately) GRD6410000T Complete kit with bars and mounting brackets Fits Quad Cab models only
Black textured powder coat finish High quality Made of durable steel Robust and one-piece construction Protects rocker panel from trail obstacles and road debris Makes it easier to get in and out of the vehicle, especially in vehicles with a suspension lift Full length slider with outer rub rail and removable full length steel step Installation in the factory holes, no drilling required Easy to install In the box: (2) Side steps Dominator DSS Hardware Notes: Fits to Crew Cab models only
Made from steel One piece design Texture black Powder coated Integrated steps allow easier access to the truck bed Integrated D-shackle mounts (shackles not included) Provisions for license plate lights Provisions for trailer light plug Port to allow access to spare tire crank Reverse sensor mounting port LED flush LED lights mount adapters included Compatible with factory receiver hitch Notes: Possibility of mounting 2" Flush Mount Rough Country lights (sold separately). However, this requires the bumper opening to be widened.
Protects vehicle from on & off-road debris Easy to install Durable, steel construction Includes (2) Rough Country LED Cubes Integrated steps for easy access to bed Retains factory receiver hitch Includes backup sensor relocators LED specs: 2880 lumens 36 watts Flood beam Each light contains 6, 3 watt high intensity Cree LEDs IP67 Waterproof rating Moisture Breather technology reduces moisture build-up behind the lens Includes premium, flat-wound wiring harness with on/off switch Durable die cast aluminum housing Dimensions: Length: 4,80" Depth: 3,11" Height: 3,63" In the box: Rear bumper (2) Rough Country Black-Series LED Flush Mount Light Wiring harness Backup sensor relocators Notes: LED are for off-road use ONLY
GO RHINO GR24132T • Pare-choc avant GO RHINO BR6 24132T
GO RHINO GR341301T • Pare-choc avant GO RHINO Element 341301T
Changing vehicle settings permanently - changes made to the vehicle permanently, will work even when the programmer is disconnected Changing vehicle settings live - changes are made live in real time and only work if the programmer is connected to the vehicle "Non-Menu" Live Functions are operations the Tazer Ram performs live, only while it is physically connected, and are not located in a menu. They are activated automatically or with button presses. List of vehicle settings (engine off): read and clear DTCs system-wide or nonspecific modules change tire size change gear ratio change Transfer Case LOW ratio enable/disable TPMS system set TPMS pressure warning limit, front and rear, between 25psi and 85psi enable/disable backup camera enable/disable Cargo Camera input (8.4" and 12" NAV UConnect only) enable/disable CD (wired audio) input enable/disable TravelLink/XM traffic and weather change daytime running lights (DRL) region (CA/USA) change DRL location enable/disable DRL Dropout function enable/disable factory fog lights enable/disable Fog Light Dropout (when fogs shut off while high beams are on) enable/disable one-touch lane change enable/disable factory halo lights (including BCM output for adding halos) configure vehicle for LED 3rd brake light change headlight type (Std/LED) change fog light type (Std/LED) change tail light type (Std/LED)/delete sensor circuit for running aftermarket lights change front turn signal type (std/LED)/delete sensor circuit for running aftermarket lights enable/disable Trailer Tow setting activate MOPAR Power Folding Mirrors activate mirror turn signals activate tow mirror lights activate approach mirror lights enable/disable Aux Buttons enable/disable Blind Spot Detection (if the hardware is added or removed) enable MOPAR power side step disable front axle disconnect module for axle swaps disable rear locker for axle swaps disable electronic steering pump for hydraulic steering conversions change cluster splash screen enable/disable PANIC button on remote one-touch return-to-stock - quick "Unmarry" function returns to stock. List of live functions (engine on): activate Light Show hold brakes at a red light enable navigation entry in-motion TurnCAM - activate backup camera when turn signals are used (5", 7", 8.4" and 12.1" UConnect) (excluding 2022 temporarily) Kill3Honk - disable three honks that sound when leaving running vehicle with keys ParkCam - activate SurroundView and front camera when front parking sensors are triggered automatically fold mirrors in/out on startup/shutdown override factory DRLs with amber DRL and turn on factory marker lights, including TRX hood lights in multiple modes (day, night or both) flash third brake light when braking customize third brake light flash pattern define Winch Mode RPM flash lights to indicate tire pressure while airing up/down Dark Mode - turn off all exterior lighting and dash/radio/shifter lights while parked with the engine running activate backup camera Force RWD (TRX only) activate 0-30 or 0-60 timer display firmware version List of "Non-Menu" Live Functions:(not in a menu - automatic or activated with button inputs only) AutoStopStart Disable - Tazer DT will automatically remember the last state of the auto stop/start system and set it for you the next time you start the vehicle AutoTracKill - Tazer DT will automatically remember the last state of the traction control system and set it for you the next time you start the vehicle Drive Mode Memory (TRX only) - Tazer DT will automatically remember drive mode and set it the next time you start the vehicle disconnect sway bar in 2WD up to 30mph or at any speed if mapped to a button Axle Locker Control - engage lockers in 2WD and 4Hi on demand. Cooldown Mode - turn on engine fans on-demand Winch Mode - raise idle RPM to user-selected value between 1300 and 2000 Line Lock - lock the front brakes for an easy burnout Rock Crawl - lock all four brakes with a steering wheel button combo to hold the vehicle still, especially helpful when off-road TC Kill - turn off traction control, stability control and ABS show backup camera (shortcut) Turn Assist - lock the inside back tire for sharper turns (button remap function only) Remap buttons to:- Any of the 8 light shows- Backup cameras- TC Kill- Line Lock- Rock Crawl- Winch Mode- Cooldown- Front/Rear/Front+Rear Lockers- SwayKill- Dark Mode- Turn Assist- Force RWD Partial Reboot Notes: Can be used with only one vehicle (lock) Compatible with only 1500 DT (2018-2024) and TRX versions (2018-2024) Does not fit Classic models 2020 and newer vehicles have tire size limit 35", after which ParkSense function will be disabled. There is no way to bypass it Updates are completely free