Filtres
Urethane coil spacers maintain factory ride Lower cam locks to correct caster for alignment Bump stop spacers to prevent harsh bottom outs Allows clearance for 33" tyres NX2 nitro series specs: Pressurized nitrogen charged twin-tube design Fluon banded piston 1-3/8" 14mm hardened chrome shaft 2" bodied shock Vehicle specific valving for better control Durable metallic silver finish High-end performance at an affordable price Lightening fast dampening adaptive to terrain Large fluon banded piston with self lubricating seals In the box: (2) Front coil spring (2) Front nitro shock NX2 (2) Front bump stop spacer (4) Front octo-cam washer (2) Rear bump stop spacer (2) Rear nitro shock NX2 (2) Rear coil spring Rear brake lines relocation Notes: Trimming may be required
Levels the vehicle Increase ground clearance for up to 35" wheels Improve factory suspension Maintains factory ride quality Easy instalation In the box: Front bump stops Front bump stops spacers Front coil springs Quicker disconnects (4) BDS NX2 shocks Note: For diesel models front get 1" lift less, we recommend to use front spacer load level kit TX1155100 (sold separately)
Lift 2" Maintains factory ride quality Increased ground clearance Easy install Coil spring specs: Powder-coated with a flexible polyester-based paint, which increases corrosion protection The material used and the production technology guarantee the preservation of the physical properties of the product for many years Shocks specs: Pressurized nitrogen charged twin-tube design Fluon banded piston 1-3/8" 14mm hardened chrome shaft 2" bodied shock Vehicle specific valving for better control Durable metallic silver finish High-end performance at an affordable price Lightening fast dampening adaptive to terrain Large fluon banded piston with self lubricating seals Front shock dimensions: Extended: 26.20" Compressed: 15.67" Travel: 10.53" Rear shock dimensions: Extended: 29.78" Compressed: 17.59" Travel: 12.19" Front shock mounts: Top mount: eyelet Bottom mount: eyelet Rear shock mounts: Top mount: eyelet Bottom mount: eyelet In the box: (2) Front coil spring (2) Front shock NX2 Nitro series (2) Front bump stop spacer (2) Front sway bar link disconnect (2) Rear coil spring Rear track bar bracket (2) Rear bump stop spacer (2) Rear sway bar link (2) Rear shock NX2 Nitro series Track bar bracket support Notes: Non-Rubicon comes from factory at lower ride height, will net slightly over 2" - final stance the same for all models Stock wheels cannot be reinstalled without spacers due to rear sway bar interference Does NOT fit with diesel models Does NOT fit with Rubicon 392 models Does NOT fit with 4XE models
Adapt suspension performance to both on-road and off-road conditions Improves handling Made of high quality materials Coil spring specs: Powder-coated with a flexible polyester-based paint, which increases corrosion protection The material used and the production technology guarantee the preservation of the physical properties of the product for many years Designed to withstand the increased load of the car (winch, steel bumper) Diameter: 0.625" Rate: 240 lbs Length: 17.25” Shocks specs: Pressurized nitrogen charged twin-tube design Fluon banded piston 1-3/8" 14mm hardened chrome shaft 2" bodied shock Vehicle specific valving for better control Durable metallic silver finish High-end performance at an affordable price Lightening fast dampening adaptive to terrain Large fluon banded piston with self lubricating seals Front shock dimensions: Extended: 22.92" Compressed: 13.92" Travel: 9" Rear shock dimensions: Extended: 21.70" Compressed: 13.42" Travel: 8.28" Front shock mounts: Top mount: stem Bottom mount: bar pin Rear shock mounts: Top mount: bar pin Bottom mount: eyelet In the box: (2) Front coil spring (2) Front shock NX2 Nitro series (2) Rear shock NX2 Nitro series (2) Add-a-leaf spring and hardware Extended u-bolts
Lift 2" Maintains factory ride quality Increased ground clearance Easy install Coil spring specs: Powder-coated with a flexible polyester-based paint, which increases corrosion protection The material used and the production technology guarantee the preservation of the physical properties of the product for many years Designed to withstand the increased load of the car (winch, steel bumper) Shocks specs: Pressurized nitrogen charged twin-tube design Fluon banded piston 1-3/8" 14mm hardened chrome shaft 2" bodied shock Vehicle specific valving for better control Durable metallic silver finish High-end performance at an affordable price Lightening fast dampening adaptive to terrain Large fluon banded piston with self lubricating seals Front shock dimensions: Extended: 22.92" Compressed: 13.92" Travel: 9" Rear shock dimensions: Extended: 22.95" Compressed: 14.67" Travel: 8.28" Front shock mounts: Top mount: stem Bottom mount: bar pin Rear shock mounts: Top mount: eyelet Bottom mount: eyelet In the box: (2) Front coil spring (2) Front shock absorber NX2 Nitro Series (2) Rear shock absorber NX2 Nitro Series (2) Rear coil spring Track bar bracket Notes: Trimming may be required
Increases ground clearance Allows larger tyres to be fitted Gives aggressive character Coil spring specs: Powder-coated with a flexible polyester-based paint, which increases corrosion protection The material used and the production technology guarantee the preservation of the physical properties of the product for many years Designed to withstand the increased load of the car (winch, steel bumper) Dedicated to cars with a gasoline engine Shocks specs: Durable metallic silver finish Vehicle specific valving for better control High-end performance at an affordable price Pressurized nitrogen charged twin-tube design Lightening fast dampening adaptive to terrain Large fluon banded piston with self lubricating seals Front shock dimensions: Extended: 22.92" Compressed: 13.92" Travel: 9" Rear shock dimensions: Extended: 22.95" Compressed: 14.67" Travel: 8.28" Front shock mounts: Top mount: stem Bottom mount: bar pin Rear shock mounts: Top mount: eyelet Bottom mount: eyelet In the box: (2) Front coil spring (2) Front nitro shock NX2 Nitro series (2) Rear coil spring (2) Rear nitro shock NX2 Nitro series Notes: Vehicles equipped with a Diesel engine may not achieve the stated heigh
Professional lift kit, designed to fit your car Ensures correct driving characteristics on the lift Adjusted to both on-road and off-road environments Improves the behavior of the lifted car In the box: (2) Front coil spring (2) Front shock NX2 Nitro series (2) Rear coil spring (2) Rear shock NX2 Nitro series
Increases ground clearance Allows larger tyres to be fitted Gives aggressive character Coil spring specs: Heavy duty Shot peened for increased tensile strength Hydraulic pre-set for reduce fatigue Polyester based powder coating Sold in pairs Shock specs: Pressurized nitrogen charged twin-tube design Fluon banded piston 1-3/8" 14mm hardened chrome shaft 2" bodied shock Vehicle specific valving for better control Durable metallic silver finish High-end performance at an affordable price Lightening fast dampening adaptive to terrain Large fluon banded piston with self lubricating seals Shock dimensions: Extended: 23.12" Compressed: 14.24" Travel: 8.88" Shock mounts: Top mount: eyelet Bottom mount: eyelet In the box: (2) Front coil spring Front strut spacers (2) Rear coil spring (2) Rear shock NX2 Nitro series Mounting kit Notes: Lift Kit dedicated to gasoline engine ONLY
2.0" Impact extruded and CNC machined 6061-T6 clear anodized aluminum one-piece body resists rust over time Clear-anodized for a durable finish Internal IFP mono-tube reservoir design Black-anodized, CNC-machined 6061-T6 billet aluminum 5/8" hard chrome plated heat-treated alloy steel Race-developed high-flow piston design Application specific valving to maximize performance Redundant sealing pack system main seal, wiper seal, scraper seal JM92 Advanced Suspension Fluid for improved performance at variable temperatures Quiet nitrile rubber allows for increased suspension articulation In the box: (2) Front nitro shock Fox Performance 2.0 IFP (2) Front coil spring (2) Front bump stop (2) Front sway bar Front adjustable track bar (2) Rear sway bar (2) Rear bump stop (2) Rear coil spring (2) Rear nitro shock Fox Performance 2.0 IFP (4) Bushing All necessary hardware Max tyre diameter: 33x12,50 17x8 Stock Sport Model No Rubbing 35x12,50 17x8 4,5-5" Sport Model Rubbing under articulation 37x12,50 17x8 Stock Rubicon No Rubbing 37x12,50 17x8 4,5-5" Rubicon Rubbing under extreme articulation Front nitro shock dimensions: Extended: 26.42" Compressed: 16.80" Travel: 9.62" Rear nitro shock dimensions: Extended: 26.92" Compressed: 16.80" Travel: 10.12" Notes: Does NOT fit with diesel models Does NOT fit with Mojave models Non-Rubicon comes from factory at lower ride height, will net slightly more lift final stance the same for all models
Lift 3" Front and rear Pro-Ride coil springs NX2 Series shock absorbers Coils made from 5160 steel Front and rear track bar relocation brackets Front sway bar links included Maintains factory ride quality Increased ground clearance Coil spring specs: Powder-coated with a flexible polyester-based paint, which increases corrosion protection Designed to withstand full coil bind Shotpeened for increased tensile strength The material used and the production technology guarantee the preservation of the physical properties of the product for many years Shocks specs: Pressurized nitrogen charged twin-tube design Fluon banded piston 1-3/8" 14 mm hardened chrome shaft 2" bodied shock Vehicle specific valving for better control Durable metallic silver finish High-end performance at an affordable price Lightening fast dampening adaptive to terrain Large fluon banded piston with self lubricating seals Front shock mounts: Top mount: stem Bottom mount: bar pin Rear shock mounts: Top mount: eyelet Bottom mount: eyelet In the box: (2) Front coil spring (2) Front shock absorber NX2 Nitro Series (2) Rear shock absorber NX2 Nitro Series (2) Rear coil spring (2) Front anti-sway bar link Track bar relocation bracket front Track bar relocation bracket rear Notes: Trimming may be required Models with V8 engine may not achieve specified lift height
Engineered with high dimensional accuracy for the perfect fit Made from durable materials to survive the test of times High-end performance In the box: (2) Front coil springs 3" (2) Add-a-leaf springs 2,5" and hardware Extended u-bolts Transfer case drop kit Front sway-bars with mounting kit (4) BDS NX2 Nitro series Notes: U-bolts fit DANA 35 rear axle ONLY. If you are looking for a lift for a vehicle equipped with a different type of axle, please constant with ours sales departament Transfer case lowering kit is not required for 2WD models
Lift 3" Gas shocks Maintains factory ride quality Increased ground clearance Easy install In the box: (2) Front shock NX2 (2) Front coil spring (2) Front bump stop (2) Front sway bar (2) Rear sway bar (2) Rear bump stop (2) Rear coil spring (2) Rear shock NX2 Adjustable track bar (4) Bushing All necessary hardware Wheel notes: 33x12.50 17x8 Stock Sport Model No Rubbing 35x12.50 17x8 4.5"-5" Sport Model Rubbing under articulation 37x12.50 17x8 Stock Rubicon No Rubbing 37x12.50 17x8 4.5"-5" Rubicon Rubbing under extreme articulation Notes: Non-Rubicon comes from factory at lower ride height, will net slightly more lift final stance the same for all models For diesel models front get 1" lift less, we recommend to use front spacer load level kit TX1155100 (sold separately)
Adapt suspension performance to both on-road and off-road conditions Improves handling Made of high quality materials Shocks specs: Pressurized nitrogen charged twin-tube design Fluon banded piston 1-3/8" 14mm hardened chrome shaft 2" bodied shock Vehicle specific valving for better control Durable metallic silver finish High-end performance at an affordable price Lightening fast dampening adaptive to terrain Large fluon banded piston with self lubricating seals Coil spring specs: Powder-coated with a flexible polyester-based paint, which increases corrosion protection The material used and the production technology guarantee the preservation of the physical properties of the product for many years Designed to withstand the increased load of the car (winch, steel bumper) Front coil spring dimensions: Diameter: 0.625" Rate: 240 lbs Length: 18.25” Rear coil spring dimensions: Diameter: 0.656" Rate: 240 lbs Length: 15.5" Front shock dimensions: Extended: 24.68" Compressed: 14.81" Travel: 9,87" Rear shock dimensions: Extended: 26.20" Compressed: 15.80" Travel: 10,40" Front shock mounts: Top mount: stem Bottom mount: bar pin Rear shock mounts: Top mount: eyelet Bottom mount: eyelet In the box: Front track bar relocation bracket (2) Front adjustable lower control arm with bushings & lubricators (2) Front NX2 Nitro series shock (2) Front coil spring (2) Front bumpstop (2) Rear NX2 Nitro series shock (2) Rear coil spring Rear sway-bar links with mounting kit Rear A-arm spacer block (2) Rear bumpstop Drop pitman arm Transfer case drop kit Notes: Vehicles equipped with Diesel engine may not achieve stated lift height Front drive line modification may be required
Professional lift kit, designed to fit your car Ensures correct driving characteristics on the lift Adjusted to both on-road and off-road environments Improves the behavior of the lifted car In the box: Front & rear cross-members Driveshaft spacer Sway-bar drops Skid plate relocation bracket Strut spacer,Rear blocks Radiator relocation bracket Bump Stops Notes: Required frame bracket modification, cutting and welding Stock wheels cannot be reinstalled with lift Check for proper tie rod end clearance if using 37x12.50 tires on 18x9 (5" BS) wheels
Levels the vehicle Increase ground clearance Allow to mount bigger wheels In the box: Knuckles Tie rod end Diff skid plate Sway bar links Bump stops Radiator relocation bracket Strut spacers Diff drop brackets Rear blocks Rear shock brackets Notes: Will fit gas and diesel models Inner Fender trimming required Minor welding required Electronic assisted steering system is sensitive to out of round, unbalanced, and more aggressive tread pattern tires. High speed steering wheel feedback can occur. Stock 17" and 18" wheels cannot be reinstalled with the lift kit Aftermarket 20" wheels with a maximum 5.25" backspacing are recommended. Certain wheel and tire combinations will require weld on steering stops
Professional lift kit, designed to fit your car Ensures correct driving characteristics on the lift Adjusted to both on-road and off-road environments Improves the behavior of the lifted car In the box: Lifted knuckles Front and rear crossmembers Upper strut spacers Driver & passenger side steering stops Front brake line brackets Differential drop brackets Bump stop brackets Sway-bar drop brackets Lower skid plate Lifted cast iron blocks U-bolts E-brake and brake line brackets 2x BDS NX2 Nitro series shocks Notes: Requires frame bracket modification and welding
Redesigned 4-link long arm to improve articulation and offer better control throughout wheel travel ProRide coil springs offer improved ride quality and more articulation Massive belly pan that incorporates the link mounts and is built to smash rocks Glideride leaf springs to provide full lift height and increased capacity Sway bar quicker disconnects and extended rear link for improved offroad flex Front HD track bar to correctly position the front axle and control lateral movement Allows clearance for 35" tyres Shocks specs: Nitrogen-charged Twin-tube design 10-stage velocity-sensitive valving Dual-welded ends for increased strength 1-3/8-inch high-flow piston Self-lubricating seals Silver powder coat finish Front shock mounts: Top mount: stem Bottom mount: eyelet Rear shock mounts: Top mount: bar pin Bottom mount: eyelet In the box: (2) Front coil spring (2) Front shock absorber NX2 Nitro Series (2) Front upper control arm (2) Front lower control arm (2) Front bump stop Front track bar Front track bar relocation bracket (2) Front disconnect sway bar link (2) Front brake line (2) Rear shock absorber NX2 Nitro Series Rear brake line (2) Leaf spring Pitman arm Crossmember Bump stops extensions (4) U-bolt (2) Shackle Hardware Notes: Fits with Chrysler 8.25 drivetrain ONLY Fits with 4.0L engine and automatic transmission models ONLY We also offer suspension kit compatible with Dana 35 - please contact our sales department CV style rear driveshaft (not included) and slip yoke eliminator kit is required CV style front driveshaft rekomendujemy Required some welding, drilling and cutting '96 and earlier models may require a longer emergency brake cable Can be purchased as a set with FOX shocks
Increased ground clearance Levels the front with the rear of the vehicle Gives an aggresive look Lift kit consists of: Front crossmember Front brake lines Front brake line brackets Front differential skid plate Break line drop brackets Steering knuckle Tie rod end Differential bracket mounting Driveshaft spacer Sway bar drop brackets Sway bar end link Rear crossmember Rear track bar bracket Bump stop extensions Upper control arms relocation brackets Strut spacers (2) FOX shocks Note: Cutting required Does NOT fit diesel models For models with LARGE hub bore ONLY Fits factory Air Ride equipped trucks only The factory Air Ride is a closed loop system. Opening the system more times than recommended in the lift instructions will require the system to be recharged. This can be done at any Ram dealer service department. A scan tool is needed to access the air control module to perform the service Frame bracket modification required Fits 4WD models equipped with factory air ride only. Stock 17" and 18" wheels cannot be re-installed, stock 20" wheels can only be re-installed with factory tire size If truck is equipped with standard hub bore use lift with standard steering knuckles BDS1697H (NX2 shocks) or BDS1697FS (FOX shocks), kits sold separately
Increased ground clearance Levels the front with the rear of the vehicle Gives an aggresive look Lift kit consists of: Front crossmember Front brake lines Front brake line brackets Front differential skid plate Break line drop brackets Steering knuckle Tie rod end Differential bracket mounting Driveshaft spacer Sway bar drop brackets Sway bar end link Rear crossmember Rear track bar bracket Bump stop extensions Upper control arms relocation brackets Strut spacers (2) NX2 shocks Note: Cutting required Does NOT fit diesel models For models with LARGE hub bore ONLY Fits factory Air Ride equipped trucks only Fits 4WD models equipped with factory air ride only. The factory Air Ride is a closed loop system. Opening the system more times than recommended in the lift instructions will require the system to be recharged. This can be done at any Ram dealer service department. A scan tool is needed to access the air control module to perform the service Frame bracket modification required Stock 17" and 18" wheels cannot be re-installed, stock 20" wheels can only be re-installed with factory tire size If truck is equipped with standard hub bore use lift with standard steering knuckles BDS1697H (NX2 shocks) or BDS1697FS (FOX shocks), kits sold separately,
Increased ground clearance Levels the front with the rear of the vehicle Clears up to 35" tires Gives an aggresive look Lift kit consists of: Front crossmember Front brake lines Front brake line brackets Front differential skid plate Break line drop brackets Steering knuckle Tie rod end Differential bracket mounting Driveshaft spacer Sway bar drop brackets Sway bar end link Rear crossmember Rear track bar bracket Bump stop extensions Upper control arms relocation brackets Strut spacers (2) BDS NX2 Nitro series shocks Note: Cutting required Does NOT fit diesel models For models with STANDARD hub bore ONLY Fits factory Air Ride equipped trucks only Fits 4WD models equipped with factory air ride only. Extreme care/caution must be taken to follow the steps of instructions or damage to the bags during installation. The factory Air Ride is a closed loop system. Opening the system more times than recommended in the lift instructions will require the system to be recharged. This can be done at any Ram dealer service department. A scan tool is needed to access the air control module to perform the service Frame bracket modification required Stock 17" and 18" wheels cannot be re-installed, stock 20" wheels can only be re-installed with factory tire size If truck is equipped with factory 22" wheels use the "large hub bore" steering knuckles lift BDS1642H (NX2 shocks) or BDS1642FS (FOX shocks), kits sold separately
Increased ground clearance Levels the front with the rear of the vehicle Clears up to 35" tires Gives an aggresive look Lift kit consists of: Front crossmember Front brake lines Front brake line brackets Front differential skid plate Break line drop brackets Steering knuckle Tie rod end Differential bracket mounting Driveshaft spacer Sway bar drop brackets Sway bar end link Rear crossmember Rear track bar bracket Bump stop extensions Upper control arms relocation brackets Strut spacers (2) Fox Performance Series 2.0 IFP shocks Note: Cutting required Does NOT fit diesel models For models with STANDARD hub bore ONLY Fits factory Air Ride equipped trucks only Fits 4WD models equipped with factory air ride only. Extreme care/caution must be taken to follow the steps of instructions or damage to the bags during installation. The factory Air Ride is a closed loop system. Opening the system more times than recommended in the lift instructions will require the system to be recharged. This can be done at any Ram dealer service department. A scan tool is needed to access the air control module to perform the service Frame bracket modification required Stock 17" and 18" wheels cannot be re-installed, stock 20" wheels can only be re-installed with factory tire size If truck is equipped with factory 22" wheels use the "large hub bore" steering knuckles lift BDS1698H (NX2 shocks) or BDS1698FS (FOX shocks), kits sold separately
Professional lift kit, designed to fit your car Ensures correct driving characteristics on the lift Adjusted to both on-road and off-road environments Improves the behavior of the lifted car In the box: Front and rear crossmembers Front brake lines Front strut spacers Tie rod ends Differential skid plate Steering knuckles Differential drop brackets Sway bar link extensions Brake line relocation brackets Bump stop extensions Rear upper control arm relocation brackets Rear track bar relocation bracket Rear sway bar links (2) Rear BDS NX2 Nitro series shocks Hardware Notes: Fits models with factory Air Ride system ONLY Fits also Air Ride Rebel models 15-18 Cutting required The factory air ride is a closed loop system. Opening the system more times than recommended in the lift instructions or factory service manual will require the system to be recharged. This can be done at any Ram dealer service department Stock 20" wheel can be reinstalled with factory sized tire ONLY. Stock 17" and 18" wheels will NOT fit This kit will bolt on Eco-Diesel models but it will require an aftermarket front drive shaft
FOX 2.5 Performance Elite coil-overs offer improved damper performance over stock DSC controller allows easy adjustment of LSC and HSC compression for performance on any terrain Performance UCAs increase strength and allow for more suspension travel FOX 2.0 performance series IFP rear shocks Increased strength and suspension travel Easy bolt on installation In the box: (2) Front upper control arm (2) Front Coil-Over Performance Elite 2.5 Reservoir adjustable DSC (2) Rear Shock 2.0 Performance IFP (2) Rear spring Notes: Will not fit models with stock pneumatic suspension Will not work with stock rims with a 12.50" wide tire If the stock rim is reinstalled it will need to be fitted with the stock-size tire ONLY Vehicles equipped with Offroad or Rebel Package will not achieve the full 3" of lift, net ride height change will be around 2" above stock
Increased ground clearance Levels the front with the rear of the vehicle Gives an aggresive look Lift kit consists of: Front cross-members Front brake line Front brake line brackets Front steering knuckle Tie rod end Differential bracket mounting Driveshaft spacer Sway bar drop brackets Skid plate Strut spacers Rear cross-members (2) FOX Nitro series shocks Notes: Cutting required Doest NOT fit diesel models Will NOT fit adjustable air suspension equipped models Fits ONLY vehicles with LARGE hub bore Stock 17" wheels cannot be reinstalled to to steering interference. Stock 20s can be reinstalled with factory tire size If truck is equipped with STANDARD hub bore use lift with standard steering knuckles BDS1663H (NX2 shocks) or BDS1663FS (FOX shocks), kit sold separately