Filtres
Front axle Tera60 TeraFlex Lift 0-6"
Front axle track bar bracket Barnes 4WD
Proudly made in the USA Fortifies your JK's axle Helps prevent axle binding Adds axle rigidity for larger weight loads Made of durable 3/6" side panels and 1/4" top spine and internal gussets Low profile design for maximum suspension up-travel In the box: Driver front truss plate Driver rear truss plate Driver top truss plate Middle front truss plate Middle rear truss plate Middle truss gusset Middle top truss plate Driver front truss plate Passenger front truss plate Passenger rear truss plate Lower C gusset spine Upper C gusset spine Lower driver C gusset plate Lower passenger C gusset plat DANA 30 upper C gusset Notes: For Jeep JK 2 Door fits 4WD models ONLY For JK DANA 30 front axles ONLY Welding required
Front axle truss kit Dana30 EVO Manufacturing ProTek
Front axle truss kit Dana44 EVO Manufacturing ProTek
Front axle truss kit Dana44 with C2 Gussets EVO Manufacturing ProTek
Triple outer O-ring Double inner seal Black hard anodized outer surface for superior corrosion resistance Notes: Fits Tera30 & Tera44 axle tubes w/ 1/2” wall
Triple outer O-ring Double inner seal Black hard anodized outer surface for superior corrosion resistance Notes: Fits Tera30 and Tera44 axle tubes w/ 1/4" wall
Front axle tube sleeves Barnes 4WD
Front axle tube sleeves Dana 30 and Dana 44 Barnes 4WD
FRONT AXLE UPGRADE LABEL PACK HILUX 1595
Proudly made in the USA Easy bolt-on installation Stronger mount than the factory bar pin setup Eliminates rattling noises produced by the factory bar pin mount Replaces the front upper bar pin shock mount Notes: Will NOT work on shocks equipped with a bonded bar pin/bushing
Rotors feature dual bolt patterns: 5x5" and 5x5.5" Improved braking performance over factory brake system 100% bolt-on upgrade w/ basic hand tools Oversized 56mm dual-piston calipers for increased clamping force and surface area Larger 13.3" (338mm) rotors for superior stopping performance (vs. 11.9" stock rotors) Slotted rotors offer better gas dissipation than smooth rotors Mill-balanced vented rotors for maximum heat dissipation Composite-resin, semi-metallic pads have excellent full temperature stopping power for maximum initial speed scrub w/ increased pad life and reduce noise and dust In the box: (2) Front brake caliper (2) Front slotted brake rotor (4) Brake pad Notes: Requires a minimum of 17” diameter wheels On 07-11 models, we recommend upgrading stock master cylinderto Mopar brake master cylinder kit with oversized bore Compatible with Teraflex brake calipers ONLY
Proudly made in USA Constructed from durable 3/16" sheet steel Protects your vehicle from off-road hazards Enhances the appearance of your XJ Flat black powder coating for increased corrosion resistance Notes: Requires drilling Requires trimming
Front Bottom Guide Plate Slide Ends Rhino Rack
FRONT BOX SECTION 50 X 20 X 1700
Front braided brake line Superior Engineering Lift 0-4"
Suitable for 0-4" lift Eliminates soft/spongy brake pedal feel Improves stopping power and responsiveness DOT approved for quality and reliability Sold separately Notes: Fits only PXII 15-18 EU models Sold individually
Suitable for 0-4" lift Eliminates soft/spongy brake pedal feel Improves stopping power and responsiveness DOT approved for quality and reliability Sold separately Notes: Fits only PX 11-15 EU models Sold individually
Front braided brake lines Superior Engineering Lift 0-4"
Length 2-3" (50-75 mm) The PTFE Teflon inner tube The braid is corrosion and flame resistant stainless steel Braided Hoses will not expand under high pressure (volumetric expansion) and temperature Eliminating that "spongy" pedal feel Notes: Fits models without ABS ONLY Fits models with 3.0Lt turbo diesel engine ONLY
Length 2-3" (50-75 mm) The PTFE Teflon inner tube The braid is corrosion and flame resistant stainless steel Braided Hoses will not expand under high pressure (volumetric expansion) and temperature Eliminating that "spongy" pedal feel Notes: Fits models without ABS ONLY Fits models with 4.8 engine ONLY
Length 2-3" (50-75 mm) The PTFE Teflon inner tube The braid is corrosion and flame resistant stainless steel Braided Hoses will not expand under high pressure (volumetric expansion) and temperature Eliminating that "spongy" pedal feel Notes: Fits models without ABS ONLY Fits models with 2.8TD, 4.2TD, 4.5 engines ONLY
Length 4-5" (100-125 mm) The PTFE Teflon inner tube The braid is corrosion and flame resistant stainless steel Braided Hoses will not expand under high pressure (volumetric expansion) and temperature Eliminating that "spongy" pedal feel Notes: Fits models without ABS ONLY Fits models with 3.0Lt turbo diesel engine ONLY