Filtres
Proudly made in the USA After lifting your Jeep TJ a CV (Double Cardan) drive shaft is a good choice to eliminate vibration issues and provide the longest lasting drive shaft Includes Brute Force Red seals Includes better quality CV joints Shaft strength is twice as strong as the factory equipped drive shaft Grease fittings are out of the way of the transmission oil pan meaning you get grease to the joints that need it and not all over the bottom of your Jeep Dimensions: Collapsed measurement: 42,86 cm Extended measurement: 51,12 cm Notes: Fits Rubicon models ONLY
Proudly made in the USA Easy bolt-on installation Made from durable 1/4" plate steel Protects your front diff from off-road hazards Allows for access to the diff drain plug Notes: Fits Dana M210 ONLY Fits Rubicon models ONLY Does NOT fit diesel models
Cast in durable nodular iron AEV logo Significantly improves the off-road protection of the differential Notes: For Jeep JL 2 Door and JL 4 Door fits Rubicon models ONLY
Proudly made in the USA Easy bolt-on installation Made from durable 1/4" plate steel Protects your front diff from off-road hazards Allows for access to the diff drain plug Notes: Fits Dana M220 ONLY Fits Rubicon models ONLY
New Dana HD Differential Covers for the new AdvanTEK axles Cast from the same high-strength, 3/8”-thick ductile-iron as our HD axle housings Red TeraFlex logo Features a large diameter fill tube/inspection port at the top to accommodate a funnel or gear oil bottle pour spout Fluid level port doubles as a mid-height inspection port In the box: Dana 44 AdvanTEK (M220) Rear HD Differential Cover All necessary hardware
New Dana HD Differential Covers for the new AdvanTEK axles Cast from the same high-strength, 3/8”-thick ductile-iron as our HD axle housings Red TeraFlex logo Features a large diameter fill tube/inspection port at the top to accommodate a funnel or gear oil bottle pour spout Fluid level port doubles as a mid-height inspection port In the box: Dana 35 AdvanTEK (M200) Rear HD differential cover kit All necessary hardware
Proudly made in the USA Easy bolt-on installation Protects your differential from off-road hazards Highly durable, constructed from 1/4" steel Fits Dana 35 axle In the box: Differential guard Hardware
Proudly made in the USA Easy installation Made from durable 1/4" plate steel Protects your rear diff from off-road hazards Notes: For Jeep JK 2 Door 07-10 fits 2WD models ONLY Fits Dana 44 axle ONLY
Proudly made in the USA Easy installation Made from durable 1/4" plate steel Protects your rear diff from off-road hazards Allows for access to the diff drain plug Notes: Does NOT fit Rubicon models Does NOT fit Willys Wheeler Edition Does NOT fit 2.0L 2 door models Does NOT fit models equipped with eTorque option
Improved braking performance over factory brake system Balanced front to rear brakes tuned specifically for lifted vehicles Machined rotor for superior stopping performance High quality brake calipers Very easy installation basic hand tools In the box: (2) Rear brake Caliper w/ 46mm piston (2) Rear solid brake Rotor (2) Rear disc brake mounting plate (4) Rear disc brake conversion brake pads Rear disc brake hose kit Brake preload spacers Hardware Notes: For Jeep XJ 84-90 fits models with non-C-clip rear axles ONLY For Jeep XJ 87-89 fits models with Dana 44 rear axles ONLY Does NOT include emergency brake cables Does NOT fit CJ and Commando Does NOT work w/ ABS sensors. You will NOT be able to install ABS sensors in the disc brake mounting kit Some factory Jeep 15” wheels may rub on the caliper. Do NOT operate the vehicle until you confirm adequate caliper/wheel clearance Most aftermarket wheels, especially alloy wheels, REQUIRE longer wheel studs when installing a disc brake You may cut a slot in the pre-load ring and slide it over the axle shaft if you do not want to replace the wheel bearings These disc brake kits REQUIRE axle shafts w/ a 2.5” bearing offset
Improved braking performance over factory brake system Easy installation High quality In the box: (2) Rear brake caliper w/ 46mm piston (2) Rear solid brake rotor (2) Rear disc brake mounting plate (4) Rear disc brake conversion brake pads Rear disc brake hose kit Emergency brake cables Brake preload spacer Hardware
Mounting place: rear Lift height: 0" R-clip to disconnect
Mounting place: rear Lift height: 0" R-clip to disconnect
Mounting place: rear Lift height: 2" R-clip to disconnect
Mounting place: rear Lift height: 2" R-clip to disconnect
Mounting place: rear Lift height: 3" R-clip to disconnect
Mounting place: rear Lift height: 3" R-clip to disconnect
Mounting place: rear Lift height: 4" R-clip to disconnect
Mounting place: rear Lift height: 4" R-clip to disconnect
Mounting place: rear Lift height: 5" R-clip to disconnect
Mounting place: rear Lift height: 5" R-clip to disconnect
Mounting place: rear Lift height: 6" R-clip to disconnect
Mounting place: rear Lift height: 6" R-clip to disconnect
Easy bolt-on installation Solid construction Recommended for cars with suspension lift Prevents possible vibrations Lowers the rear driveline center support mount to improve driveline angles during full droop In the box: (2) Rear driveline center support mount lowering spacers Hardware