Filtres
Adapt suspension performance to both on-road and off-road conditions Improves handling Made of high quality materials Shocks specs: Pressurized nitrogen charged twin-tube design Fluon banded piston 1-3/8" 14mm hardened chrome shaft 2" bodied shock Vehicle specific valving for better control Durable metallic silver finish High-end performance at an affordable price Lightening fast dampening adaptive to terrain Large fluon banded piston with self lubricating seals Coil spring specs: Powder-coated with a flexible polyester-based paint, which increases corrosion protection The material used and the production technology guarantee the preservation of the physical properties of the product for many years Designed to withstand the increased load of the car (winch, steel bumper) Front coil spring dimensions: Diameter: 0.625" Rate: 240 lbs Length: 18.25” Rear coil spring dimensions: Diameter: 0.656" Rate: 240 lbs Length: 15.5" Front shock dimensions: Extended: 24.68" Compressed: 14.81" Travel: 9,87" Rear shock dimensions: Extended: 26.20" Compressed: 15.80" Travel: 10,40" Front shock mounts: Top mount: stem Bottom mount: bar pin Rear shock mounts: Top mount: eyelet Bottom mount: eyelet In the box: Front track bar relocation bracket (2) Front adjustable lower control arm with bushings & lubricators (2) Front NX2 Nitro series shock (2) Front coil spring (2) Front bumpstop (2) Rear NX2 Nitro series shock (2) Rear coil spring Rear sway-bar links with mounting kit Rear A-arm spacer block (2) Rear bumpstop Drop pitman arm Transfer case drop kit Notes: Vehicles equipped with Diesel engine may not achieve stated lift height Front drive line modification may be required
Professional lift kit, designed to fit your car Ensures correct driving characteristics on the lift Adjusted to both on-road and off-road environments Improves the behavior of the lifted car In the box: Front & rear cross-members Driveshaft spacer Sway-bar drops Skid plate relocation bracket Strut spacer,Rear blocks Radiator relocation bracket Bump Stops Notes: Required frame bracket modification, cutting and welding Stock wheels cannot be reinstalled with lift Check for proper tie rod end clearance if using 37x12.50 tires on 18x9 (5" BS) wheels
Levels the vehicle Increase ground clearance Allow to mount bigger wheels In the box: Knuckles Tie rod end Diff skid plate Sway bar links Bump stops Radiator relocation bracket Strut spacers Diff drop brackets Rear blocks Rear shock brackets Notes: Will fit gas and diesel models Inner Fender trimming required Minor welding required Electronic assisted steering system is sensitive to out of round, unbalanced, and more aggressive tread pattern tires. High speed steering wheel feedback can occur. Stock 17" and 18" wheels cannot be reinstalled with the lift kit Aftermarket 20" wheels with a maximum 5.25" backspacing are recommended. Certain wheel and tire combinations will require weld on steering stops
Professional lift kit, designed to fit your car Ensures correct driving characteristics on the lift Adjusted to both on-road and off-road environments Improves the behavior of the lifted car In the box: Lifted knuckles Front and rear crossmembers Upper strut spacers Driver & passenger side steering stops Front brake line brackets Differential drop brackets Bump stop brackets Sway-bar drop brackets Lower skid plate Lifted cast iron blocks U-bolts E-brake and brake line brackets 2x BDS NX2 Nitro series shocks Notes: Requires frame bracket modification and welding
Redesigned 4-link long arm to improve articulation and offer better control throughout wheel travel ProRide coil springs offer improved ride quality and more articulation Massive belly pan that incorporates the link mounts and is built to smash rocks Glideride leaf springs to provide full lift height and increased capacity Sway bar quicker disconnects and extended rear link for improved offroad flex Front HD track bar to correctly position the front axle and control lateral movement Allows clearance for 35" tyres Shocks specs: Nitrogen-charged Twin-tube design 10-stage velocity-sensitive valving Dual-welded ends for increased strength 1-3/8-inch high-flow piston Self-lubricating seals Silver powder coat finish Front shock mounts: Top mount: stem Bottom mount: eyelet Rear shock mounts: Top mount: bar pin Bottom mount: eyelet In the box: (2) Front coil spring (2) Front shock absorber NX2 Nitro Series (2) Front upper control arm (2) Front lower control arm (2) Front bump stop Front track bar Front track bar relocation bracket (2) Front disconnect sway bar link (2) Front brake line (2) Rear shock absorber NX2 Nitro Series Rear brake line (2) Leaf spring Pitman arm Crossmember Bump stops extensions (4) U-bolt (2) Shackle Hardware Notes: Fits with Chrysler 8.25 drivetrain ONLY Fits with 4.0L engine and automatic transmission models ONLY We also offer suspension kit compatible with Dana 35 - please contact our sales department CV style rear driveshaft (not included) and slip yoke eliminator kit is required CV style front driveshaft rekomendujemy Required some welding, drilling and cutting '96 and earlier models may require a longer emergency brake cable Can be purchased as a set with FOX shocks
Increased ground clearance Levels the front with the rear of the vehicle Gives an aggresive look Lift kit consists of: Front crossmember Front brake lines Front brake line brackets Front differential skid plate Break line drop brackets Steering knuckle Tie rod end Differential bracket mounting Driveshaft spacer Sway bar drop brackets Sway bar end link Rear crossmember Rear track bar bracket Bump stop extensions Upper control arms relocation brackets Strut spacers (2) FOX shocks Note: Cutting required Does NOT fit diesel models For models with LARGE hub bore ONLY Fits factory Air Ride equipped trucks only The factory Air Ride is a closed loop system. Opening the system more times than recommended in the lift instructions will require the system to be recharged. This can be done at any Ram dealer service department. A scan tool is needed to access the air control module to perform the service Frame bracket modification required Fits 4WD models equipped with factory air ride only. Stock 17" and 18" wheels cannot be re-installed, stock 20" wheels can only be re-installed with factory tire size If truck is equipped with standard hub bore use lift with standard steering knuckles BDS1697H (NX2 shocks) or BDS1697FS (FOX shocks), kits sold separately
Increased ground clearance Levels the front with the rear of the vehicle Gives an aggresive look Lift kit consists of: Front crossmember Front brake lines Front brake line brackets Front differential skid plate Break line drop brackets Steering knuckle Tie rod end Differential bracket mounting Driveshaft spacer Sway bar drop brackets Sway bar end link Rear crossmember Rear track bar bracket Bump stop extensions Upper control arms relocation brackets Strut spacers (2) NX2 shocks Note: Cutting required Does NOT fit diesel models For models with LARGE hub bore ONLY Fits factory Air Ride equipped trucks only Fits 4WD models equipped with factory air ride only. The factory Air Ride is a closed loop system. Opening the system more times than recommended in the lift instructions will require the system to be recharged. This can be done at any Ram dealer service department. A scan tool is needed to access the air control module to perform the service Frame bracket modification required Stock 17" and 18" wheels cannot be re-installed, stock 20" wheels can only be re-installed with factory tire size If truck is equipped with standard hub bore use lift with standard steering knuckles BDS1697H (NX2 shocks) or BDS1697FS (FOX shocks), kits sold separately,
Increased ground clearance Levels the front with the rear of the vehicle Clears up to 35" tires Gives an aggresive look Lift kit consists of: Front crossmember Front brake lines Front brake line brackets Front differential skid plate Break line drop brackets Steering knuckle Tie rod end Differential bracket mounting Driveshaft spacer Sway bar drop brackets Sway bar end link Rear crossmember Rear track bar bracket Bump stop extensions Upper control arms relocation brackets Strut spacers (2) BDS NX2 Nitro series shocks Note: Cutting required Does NOT fit diesel models For models with STANDARD hub bore ONLY Fits factory Air Ride equipped trucks only Fits 4WD models equipped with factory air ride only. Extreme care/caution must be taken to follow the steps of instructions or damage to the bags during installation. The factory Air Ride is a closed loop system. Opening the system more times than recommended in the lift instructions will require the system to be recharged. This can be done at any Ram dealer service department. A scan tool is needed to access the air control module to perform the service Frame bracket modification required Stock 17" and 18" wheels cannot be re-installed, stock 20" wheels can only be re-installed with factory tire size If truck is equipped with factory 22" wheels use the "large hub bore" steering knuckles lift BDS1642H (NX2 shocks) or BDS1642FS (FOX shocks), kits sold separately
Increased ground clearance Levels the front with the rear of the vehicle Clears up to 35" tires Gives an aggresive look Lift kit consists of: Front crossmember Front brake lines Front brake line brackets Front differential skid plate Break line drop brackets Steering knuckle Tie rod end Differential bracket mounting Driveshaft spacer Sway bar drop brackets Sway bar end link Rear crossmember Rear track bar bracket Bump stop extensions Upper control arms relocation brackets Strut spacers (2) Fox Performance Series 2.0 IFP shocks Note: Cutting required Does NOT fit diesel models For models with STANDARD hub bore ONLY Fits factory Air Ride equipped trucks only Fits 4WD models equipped with factory air ride only. Extreme care/caution must be taken to follow the steps of instructions or damage to the bags during installation. The factory Air Ride is a closed loop system. Opening the system more times than recommended in the lift instructions will require the system to be recharged. This can be done at any Ram dealer service department. A scan tool is needed to access the air control module to perform the service Frame bracket modification required Stock 17" and 18" wheels cannot be re-installed, stock 20" wheels can only be re-installed with factory tire size If truck is equipped with factory 22" wheels use the "large hub bore" steering knuckles lift BDS1698H (NX2 shocks) or BDS1698FS (FOX shocks), kits sold separately
Professional lift kit, designed to fit your car Ensures correct driving characteristics on the lift Adjusted to both on-road and off-road environments Improves the behavior of the lifted car In the box: Front and rear crossmembers Front brake lines Front strut spacers Tie rod ends Differential skid plate Steering knuckles Differential drop brackets Sway bar link extensions Brake line relocation brackets Bump stop extensions Rear upper control arm relocation brackets Rear track bar relocation bracket Rear sway bar links (2) Rear BDS NX2 Nitro series shocks Hardware Notes: Fits models with factory Air Ride system ONLY Fits also Air Ride Rebel models 15-18 Cutting required The factory air ride is a closed loop system. Opening the system more times than recommended in the lift instructions or factory service manual will require the system to be recharged. This can be done at any Ram dealer service department Stock 20" wheel can be reinstalled with factory sized tire ONLY. Stock 17" and 18" wheels will NOT fit This kit will bolt on Eco-Diesel models but it will require an aftermarket front drive shaft
FOX 2.5 Performance Elite coil-overs offer improved damper performance over stock DSC controller allows easy adjustment of LSC and HSC compression for performance on any terrain Performance UCAs increase strength and allow for more suspension travel FOX 2.0 performance series IFP rear shocks Increased strength and suspension travel Easy bolt on installation In the box: (2) Front upper control arm (2) Front Coil-Over Performance Elite 2.5 Reservoir adjustable DSC (2) Rear Shock 2.0 Performance IFP (2) Rear spring Notes: Will not fit models with stock pneumatic suspension Will not work with stock rims with a 12.50" wide tire If the stock rim is reinstalled it will need to be fitted with the stock-size tire ONLY Vehicles equipped with Offroad or Rebel Package will not achieve the full 3" of lift, net ride height change will be around 2" above stock
Increased ground clearance Levels the front with the rear of the vehicle Gives an aggresive look Lift kit consists of: Front cross-members Front brake line Front brake line brackets Front steering knuckle Tie rod end Differential bracket mounting Driveshaft spacer Sway bar drop brackets Skid plate Strut spacers Rear cross-members (2) FOX Nitro series shocks Notes: Cutting required Doest NOT fit diesel models Will NOT fit adjustable air suspension equipped models Fits ONLY vehicles with LARGE hub bore Stock 17" wheels cannot be reinstalled to to steering interference. Stock 20s can be reinstalled with factory tire size If truck is equipped with STANDARD hub bore use lift with standard steering knuckles BDS1663H (NX2 shocks) or BDS1663FS (FOX shocks), kit sold separately
Increased ground clearance Levels the front with the rear of the vehicle Gives an aggresive look Lift kit consists of: Front cross-members Front brake line Front brake line brackets Front steering knuckle Tie rod end Differential bracket mounting Driveshaft spacer Sway bar drop brackets Skid plate Strut spacers Rear cross-members (2) BDS NX2 Nitro series shocks Notes: Cutting required Doest NOT fit diesel models Will NOT fit adjustable air ride models Fits ONLY vehicles with LARGE hub bore Stock 17" wheels cannot be reinstalled to to steering interference. Stock 20s can be reinstalled with factory tire size For models with STANDARD bore You must to buy lift kit BDS1663FS (with Fox shocks) or lift kit BDS1663H (with NX2 shocks), sold separately
Levels the front with the rear of the vehicle Increased ground clearance Corrects suspension, steering, & driveline geometry Lift consists of: Front Crossmember Front Brake Line Front Brake Line Brackes Front Steering Knuckles Tie Rod End w/Nut Skid Plate Differential drop brackets Sway bar drop brackets Drive Shaft Spacer Rear Crossmember Bump stop extension Relocation brackets Sway bar links Coil spring (2) shocks BDS NX2 Notes: Cutting required Does NOT fit diesel models Fits ONLY vehicles with LARGE hub bore Will NOT fit adjustable air suspension equipped models RAMs with factory 22" wheels require the larger bore knuckles due to larger wheel bearing assembly. Reference build code WPM or WPZ. Stock 17" wheels cannot be reinstalled to to steering interference. Stock 20s can be reinstalled with factory tire size This system will NOT fit vehicles equipped with STANDARD hub bore If truck is equipped with STANDARD hub bore use lift with standard steering knuckles BDS1661H (NX2 shocks) or BDS1661F (FOX shocks), kit sold separately
Increased ground clearance Levels the front with the rear of the vehicle Gives an aggresive look In the box: Front cross-members Front brake line Front brake line brackets Front steering knuckle Tie rod end Differential bracket mounting Driveshaft spacer Sway bar drop brackets Skid plate Strut spacers Rear cross-members (2) BDS NX2 Nitro series shocks Notes: Cutting required Fits ONLY vehicles with STANDARD hub bore This kit will NOT work on Diesel models. RAMs with factory 22" wheels require the larger bore knuckles due to larger wheel bearing assembly. Reference build code WPM or WPZ Will NOT fit adjustable "air ride" suspension equipped models Stock 17" wheels cannot be reinstalled to to steering interference. Stock 20s can be reinstalled with factory tire size For models with large bore You must to buy lift kit BDS1664FS (with Fox shocks) or lift kit BDS1664H (with NX2 shocks), sold separately
Levels the front with the rear of the vehicle Increased ground clearance Corrects suspension, steering, & driveline geometry Lift consists of: Front Crossmember Front Brake Line Front Brake Line Brackes Front Steering Knuckles Tie Rod End w/Nut Skid Plate Differential drop brackets Sway bar drop brackets Drive Shaft Spacer Rear Crossmember Bump stop extension Relocation brackets Sway bar links Coil spring (2) shocks BDS NX2 Notes: Cutting required Fits ONLY vehicles with STANDARD hub bore RAMs with factory 22" wheels require the larger bore knuckles due to larger wheel bearing assembly. Reference build code WPM or WPZ Will NOT fit adjustable "air ride" suspension equipped models If installing the 6" kit on a Rebel or truck equipped with. an "off road group package" the truck will sit roughly 1/2" front high with the preload spacer installed. If the preload spacer isn't installed the truck will sit about 3/8" now low. Stock 17" wheels cannot be reinstalled to to steering interference. Stock 20s can be reinstalled with factory tire size This kit will NOT work on Diesel models. If truck is equipped with LARGE hub bore use lift with standard steering knuckles BDS1662H (NX2 shocks) or BDS1662F (FOX shocks), kit sold separately If installing the 6" kit on a Rebel or truck equipped with. an “off road group package” the truck will sit roughly 1/2" front high with the preload spacer installed. If the preload spacer isn’t installed the truck will sit about 3/8" front low. Neither will have a level stance.
Professional lift kit, designed to fit your car Ensures correct driving characteristics on the lift Adjusted to both on-road and off-road environments Improves the behavior of the lifted car In the box: Front & rear cross-members Driveshaft spacer Sway-bar links Skid plate Strut spacers Rear sway-bar links Front brake line brackets Bump-stop brackets 2x rear BDS NX2 Nitro series shocks Notes: For models without Air - Ride Cutting required
Pressurized nitrogen charged twin-tube design Fluon banded piston 1-3/8" 14mm hardened chrome shaft 2" bodied shock Vehicle specific valving for better control Durable metallic silver finish High-end performance at an affordable price Lightening fast dampening adaptive to terrain Large fluon banded piston with self lubricating seals Rear shock dimensions: Extended: 27.91" Compressed: 16.55" Travel: 11.36" Rear shock mounts: Top mount: eyelet Bottom mount: eyelet In the box: Front cross-members Front brake line brackets (2) Rear sway-bar link Rear cross-members (2) Rear BDS NX2 Nitro series shock Bump stops Driveshaft spacer Sway-bar links Control Arm Relocation Skid plate Strut spacers Notes: Fits model without Air-Ride Cutting required
Allows larger wheels to be mounted Increased ground clearance Corrects suspension, steering, & driveline geometry In the box: (2) Front brake line (2) Front Shock absorber NX2 (1) Rear brake line (2) Rear Shock absorber NX2 (2) Sway bar link kit (4) Leaf spring 5" (4) Bump stop Front track bar bracket Pitman Arm U-bolts Hardware Notes: May require larger diameter driveshaft if equipped with a 41-1/2" front driveshaft A slip yoke eliminator and dual cardan style rear driveshaft is required Extended shackles recommended to clear the military wraps on the springs Pitman arms will NOT fit Yj models equiped with manual steering
Increased ground clearance Levels the front with the rear of the vehicle Gives an aggresive look Lift consists of: Front Crossmember Front Brake Line Front Brake Line Brackes Front Steering Knuckles Tie Rod End w/Nut Skid Plate Differential drop brackets Sway bar drop brackets Drive Shaft Spacer Rear Crossmember Bump stop extension Relocation brackets Strut spacer box kit (2) Rear shocks Fox Performance 2.0 IFP Notes: Cutting required Fits ONLY vehicles with STANDARD hub bore RAMs with factory 22" wheels require the larger bore knuckles due to larger wheel bearing assembly. Reference build code WPM or WPZ Will NOT fit adjustable "air ride" suspension equipped models Will NOT fit 2019 RAM 1500 Classic models, Refer to the 2018 kit listings Stock 17" wheels cannot be reinstalled to to steering interference. Stock 20s can be reinstalled with factory tire size This kit will NOT work on Diesel models. For models with large bore You must to buy lift kit BDS1664FS (with Fox shocks) or lift kit BDS1664H (with NX2 shocks), sold separately
Levels vehicle Gives aggressive look Easy installation Increased ground clearance Shocks specs: 46mm monotube design ensures consistent, fade-free performance in all conditions Self-adjusting deflective disc valving reacts immediately to surface changes enabling maximum vehicle control Remote reservoir increases shock oil capacity for greater heat dissipation Designed to easily install in vehicle's stock mounting locations Unique swivel reservoir banjo fitting allows 360° rotation In the box: Front left side B8 5160 shock Front right side B8 5160 shock (2) Rear B8 516 shocks (2) Front springs (2) Rear springs Notes: Front springs levels up to 2" (without steel bumper) Fitment: Mercedes G-Class 79-18 | Front 0 kg | Rear up to 150-300kg | Lift 2"
