Filtres
Proudly made in the USA Easy bolt-on installation Improves control and handling Reduces bump steer Reduces tie rod and ball joint wear and tear In the box: (2) N3 Steering stabilizers Mounting brackets Hardware Notes: Fits models equipped with 2-8" of suspension lift ONLY Does NOT fit stock height models
Proudly made in the USA Flat black Tyre coverage: 2" / 5,08 cm Flare height: 6,25" / 15,87 cm Simulated riveted look Quick and easy install with no drilling Added protection from rocks, mud and other road debris UV protected to prevent fading Built from a special Tri-Blend ABS material for maximum strength and durability Easily paintable to color match your truck Can be removed to bring truck back to stock In the box: (2) Front fender flare (2) Rear fender flare Hardware Notes: Does NOT fit models equipped with Tremor package
DOT approved Braided stainless steel exterior Offers superior protection from off-road debris Pressure tested to 4,000PSI Length: 33,5" Notes: Fits Super Duty models ONLY Recommended for models with 4,5-6" suspension lift kits
Advanced foam-cell technology Vehicle specific multi-stage valving Increased fluid capacity for max heat dissipation 180° directional mounting Construction ensures solid contact between tire and road Twin tube construction Chrome plated shaft Sintered iron piston Black boot included Dimensions: Extended: 22,63" Compressed: 13,75" Travel: 8,88" Mounts: Top mount: stud Bottom mount: eyelet Notes: Fits with 4WD Super Duty models ONLY
Advanced foam-cell technology Vehicle specific multi-stage valving Increased fluid capacity for max heat dissipation 180° directional mounting Construction ensures solid contact between tire and road Twin tube construction Chrome plated shaft Sintered iron piston Black boot included Dimensions: Extended: 24,63" Compressed: 14,75" Travel: 9,88" Mounts: Top mount: stud Bottom mount: eyelet Notes: Fits with 4WD models ONLY F250, F350 17-20 fits with 4WD Super Duty models ONLY
Advanced foam-cell technology Vehicle specific multi-stage valving Increased fluid capacity for max heat dissipation 180° directional mounting Construction ensures solid contact between tire and road Twin tube construction Chrome plated shaft Sintered iron piston Black boot included Dimensions: Extended: 26,65" Compressed: 15,87" Travel: 10,78" Mounts: Top mount: stud Bottom mount: eyelet Notes: Fits with 4WD models ONLY Ford F350 17-present fits with 4WD Super Duty models ONLY
Advanced foam-cell technology Vehicle specific multi-stage valving Increased fluid capacity for max heat dissipation 180° directional mounting Construction ensures solid contact between tire and road Twin tube construction Chrome plated shaft Sintered iron piston Black boot included Dimensions: Extended: 28,75" Compressed: 16,5" Travel: 12,25" Mounts: Top mount: stud Bottom mount: eyelet Notes: Ford F250, F350 05-16 fits with Super Duty 4WD models ONLY Ford F250, F350 17-20 fits with 4WD models ONLY
Body: 2.5" smooth bore zinc plated seamless steel body Body Plating: Zinc-plated and double-clear coated for long lasting finish Reservoir: 2.5" Smooth bore and honed seamless alloy reservoir Components: Black-anodized, CNC-machined 6061-T6 billet aluminum Shaft: 7/8" hard chrome plated heat-treated alloy steel Piston: Race-developed high-flow piston design Valving: Application specific valving to maximize performance Seals: Redundant sealing pack system main seal, wiper seal, scraper seal Bearing: PTFE-lined, heat-treated, alloy steel spherical Dimensions: Extended: 24.45" Compressed: 15.69" Travel: 8.76" Mounts: Top mount: stem top Bottom mount: eyelet Notes: Fits 4WD models ONLY
Body: 2.5" smooth bore zinc plated seamless steel body Body Plating: Zinc-plated and double-clear coated for long lasting finish Reservoir: 2.5" Smooth bore and honed seamless alloy reservoir Components: Black-anodized, CNC-machined 6061-T6 billet aluminum Shaft: 7/8" hard chrome plated heat-treated alloy steel Piston: Race-developed high-flow piston design Valving: Application specific valving to maximize performance Seals: Redundant sealing pack system main seal, wiper seal, scraper seal Bearing: PTFE-lined, heat-treated, alloy steel spherical Dimensions: Extended: 26.94" Compressed: 16.89" Travel: 10.05" Mounts: Top mount: stem top Bottom mount: eyelet Notes: Fits 4WD models ONLY
2.0” Impact extruded and CNC machined 6061-T6 clear anodized aluminum one-piece body resists rust over time Clear-anodized for a durable finish Internal IFP mono-tube reservoir design Black-anodized, CNC-machined 6061-T6 billet aluminum Shaft: 5/8" hard chrome plated heat-treated alloy steel Race-developed high-flow piston design Application specific valving to maximize performance Redundant sealing pack system main seal, wiper seal, scraper seal JM92 Advanced Suspension Fluid for improved performance at variable temperatures Quiet nitrile rubber allows for increased suspension articulation Dimensions: Extended: 22.28" Compressed: 13.90" Travel: 8.13" Mounts: Top mount: stem top Bottom mount: eyelet
2.0” Impact extruded and CNC machined 6061-T6 clear anodized aluminum one-piece body resists rust over time Clear-anodized for a durable finish Internal IFP mono-tube reservoir design Black-anodized, CNC-machined 6061-T6 billet aluminum Shaft: 5/8" hard chrome plated heat-treated alloy steel Race-developed high-flow piston design Application specific valving to maximize performance Redundant sealing pack system main seal, wiper seal, scraper seal JM92 Advanced Suspension Fluid for improved performance at variable temperatures Quiet nitrile rubber allows for increased suspension articulation Dimensions: Extended: 24.00" Compressed: 15.00" Travel: 8.75" Mounts: Top mount: stem top Bottom mount: eyelet Notes: Fits 4WD models ONLY
2.0” Impact extruded and CNC machined 6061-T6 clear anodized aluminum one-piece body resists rust over time Clear-anodized for a durable finish Internal IFP mono-tube reservoir design Black-anodized, CNC-machined 6061-T6 billet aluminum Shaft: 5/8" hard chrome plated heat-treated alloy steel Race-developed high-flow piston design Application specific valving to maximize performance Redundant sealing pack system main seal, wiper seal, scraper seal JM92 Advanced Suspension Fluid for improved performance at variable temperatures Quiet nitrile rubber allows for increased suspension articulation Dimensions: Extended: 25.98" Compressed: 16.10" Travel: 9.63" Mounts: Top mount: stem top Bottom mount: eyelet Notes: Fits 4WD models ONLY
2.0” Impact extruded and CNC machined 6061-T6 clear anodized aluminum one-piece body resists rust over time Clear-anodized for a durable finish Internal IFP mono-tube reservoir design Black-anodized, CNC-machined 6061-T6 billet aluminum Shaft: 5/8" hard chrome plated heat-treated alloy steel Race-developed high-flow piston design Application specific valving to maximize performance Redundant sealing pack system main seal, wiper seal, scraper seal JM92 Advanced Suspension Fluid for improved performance at variable temperatures Quiet nitrile rubber allows for increased suspension articulation Dimensions: Extended: 27.58" Compressed: 16.70" Travel: 10.63" Mounts: Top mount: stem top Bottom mount: eyelet Notes: Fits 4WD models ONLY
2.0" Impact extruded 6061-T6 aluminum will resist rust over time Clear-anodized for a durable finish 2.0" Smooth bore 6061-T6 Aluminum is hard anodized Black-anodized, CNC-machined 6061-T6 billet aluminum Shaft: 5/8" hard chrome plated heat-treated alloy steel Race-developed high-flow piston design Application specific valving to maximize performance JM92 Advanced Suspension Fluid for improved performance at variable temperatures LSC - Low Speed Compression Dimensions: Extended 22.37" Compressed: 13.75" Travel: 8.62" Mounts: Top mount: stem top Bottom mount: eyelet Notes: Includes universal bracket
2.0" Impact extruded 6061-T6 aluminum will resist rust over time Clear-anodized for a durable finish 2.0" Smooth bore 6061-T6 Aluminum is hard anodized Black-anodized, CNC-machined 6061-T6 billet aluminum Shaft: 5/8" hard chrome plated heat-treated alloy steel Race-developed high-flow piston design Application specific valving to maximize performance JM92 Advanced Suspension Fluid for improved performance at variable temperatures LSC - Low Speed Compression Dimensions: Extended 24.00" Compressed: 14.75" Travel: 9.25" Mounts: Top mount: stem top Bottom mount: eyelet Notes: Includes universal bracket
Body: 2.0” Impact extruded and CNC machined 6061-T6 clear anodized aluminum one-piece body resists rust over time Reservoir: External reservoir to increase the damping level Body Plating: Clear-anodized for a durable finish Components: Black-anodized, CNC-machined 6061-T6 billet aluminum Shaft: 5/8" hard chrome plated heat-treated alloy steel Piston: Race-developed high-flow piston design Seals: Redundant sealing pack system main seal, wiper seal, and scraper seal Oil: JM92 Advanced Suspension Fluid for improved performance at variable temperatures Dimensions: Extended 22.37" Compressed: 13.75" Travel: 8.62" Mounts: Top mount: stem top Bottom mount: eyelet Notes: Includes universal reservoir bracket
Body: 2.0” Impact extruded and CNC machined 6061-T6 clear anodized aluminum one-piece body resists rust over time Reservoir: External reservoir to increase the damping level Body Plating: Clear-anodized for a durable finish Components: Black-anodized, CNC-machined 6061-T6 billet aluminum Shaft: 5/8" hard chrome plated heat-treated alloy steel Piston: Race-developed high-flow piston design Seals: Redundant sealing pack system main seal, wiper seal, and scraper seal Oil: JM92 Advanced Suspension Fluid for improved performance at variable temperatures Dimensions: Extended 24.00" Compressed: 14.75" Travel: 9.25" Mounts: Top mount: stem top Bottom mount: eyelet Notes: Includes universal reservoir bracket
Body: 2.0” Impact extruded and CNC machined 6061-T6 clear anodized aluminum one-piece body resists rust over time Reservoir: External reservoir to increase the damping level Body Plating: Clear-anodized for a durable finish Components: Black-anodized, CNC-machined 6061-T6 billet aluminum Shaft: 5/8" hard chrome plated heat-treated alloy steel Piston: Race-developed high-flow piston design Seals: Redundant sealing pack system main seal, wiper seal, and scraper seal Oil: JM92 Advanced Suspension Fluid for improved performance at variable temperatures Dimensions: Extended 25.87" Compressed: 15.75" Travel: 10.12" Mounts: Top mount: stem top Bottom mount: eyelet Notes: Includes universal reservoir bracket
Body: 2.0” Impact extruded and CNC machined 6061-T6 clear anodized aluminum one-piece body resists rust over time Reservoir: External reservoir to increase the damping level Body Plating: Clear-anodized for a durable finish Components: Black-anodized, CNC-machined 6061-T6 billet aluminum Shaft: 5/8" hard chrome plated heat-treated alloy steel Piston: Race-developed high-flow piston design Seals: Redundant sealing pack system main seal, wiper seal, and scraper seal Oil: JM92 Advanced Suspension Fluid for improved performance at variable temperatures Dimensions: Extended 27.37" Compressed: 16.25" Travel: 11.12" Mounts: Top mount: stem top Bottom mount: eyelet Notes: Includes reservoir clamp
DSC - Dual Speed Compression Body: 2.5” Impact extruded and CNC machined 6061-T6 clear anodized aluminum one-piece body resists rust over time Reservoir: 2,5" Smooth bore and honed seamless alloy reservoir Body Plating: Zinc-plated and double-clear coated for long lasting finish Components: Black-anodized, CNC-machined 6061-T6 billet aluminum Shaft: 7/8" hard chrome plated heat-treated alloy steel Piston: Race-developed high-flow piston design Seals: Redundant sealing pack system main seal, wiper seal, and scraper seal Oil: JM92 Advanced Suspension Fluid for improved performance at variable temperatures Adjuster: DSC allows 10 separate low-speed and 12 high-speed compression levels Dimensions: Extended: 22.29" Compressed: 14.81" Travel: 7.48" Mounts: Top mount: stem top Bottom mount: eyelet
DSC - Dual Speed Compression Body: 2.5” Impact extruded and CNC machined 6061-T6 clear anodized aluminum one-piece body resists rust over time Reservoir: 2,5" Smooth bore and honed seamless alloy reservoir Body Plating: Zinc-plated and double-clear coated for long lasting finish Components: Black-anodized, CNC-machined 6061-T6 billet aluminum Shaft: 7/8" hard chrome plated heat-treated alloy steel Piston: Race-developed high-flow piston design Seals: Redundant sealing pack system main seal, wiper seal, and scraper seal Oil: JM92 Advanced Suspension Fluid for improved performance at variable temperatures Adjuster: DSC allows 10 separate low-speed and 12 high-speed compression levels Dimensions: Extended: 24.79" Compressed: 16.01" Travel: 8.78" Mounts: Top mount: stem top Bottom mount: eyelet
DSC - Dual Speed Compression Body: 2.5” Impact extruded and CNC machined 6061-T6 clear anodized aluminum one-piece body resists rust over time Reservoir: 2,5" Smooth bore and honed seamless alloy reservoir Body Plating: Zinc-plated and double-clear coated for long lasting finish Components: Black-anodized, CNC-machined 6061-T6 billet aluminum Shaft: 7/8" hard chrome plated heat-treated alloy steel Piston: Race-developed high-flow piston design Seals: Redundant sealing pack system main seal, wiper seal, and scraper seal Oil: JM92 Advanced Suspension Fluid for improved performance at variable temperatures Adjuster: DSC allows 10 separate low-speed and 12 high-speed compression levels Dimensions: Extended: 27.29" Compressed: 17.31" Travel: 9.98" Mounts: Top mount: stem top Bottom mount: eyelet
Multi- stage velocity sensitive valving Twin tube construction Bonded iron piston Chromed piston rod with micro pores Red polyurethane bushings Dimensions: Extended: 22,63" Compressed: 13,75" Travel: 8,88" Mounts: Top mount: stud Bottom mount: eyelet Notes: Shock must be mounted body down Ford F250 Super Duty 05-11 fits with 4WD models ONLY Ford F250 Super Duty 17-20 fits with 4WD models ONLY Ford F350 Super Duty 05-08 fits with 4WD models ONLY Ford F350 Super Duty 19-20 fits with 4WD models ONLY
Multi- stage velocity sensitive valving Twin tube construction Bonded iron piston Chromed piston rod with micro pores Red polyurethane bushings Dimensions: Extended: 24,63" Compressed: 14,75" Travel: 9,88" Mounts: Top mount: stud Bottom mount: eyelet Notes: Shock must be mounted body down RAM 2500 14-20 fits with 4WD models ONLY RAM 3500 13-20 fits with 4WD models ONLY F250, F350 Super Duty 17-20 fits with 4WD models ONLY
Multi- stage velocity sensitive valving Twin tube construction Bonded iron piston Chromed piston rod with micro pores Red polyurethane bushings Dimensions: Extended: 26,65" Compressed: 15,87" Travel: 10,78" Mounts: Top mount: stud Bottom mount: eyelet Notes: Shock must be mounted body down RAM 2500 14-20 fits with 4WD models ONLY Ford F250 17-20 fits with 4WD models ONLY RAM 3500 13-20 fits with 4WD models ONLY Ford F350 Super Duty 17-20 fits with 4WD models ONLY
Flush, low-profile design Durable aircraft grade aluminum Convenient tri-fold design Secure track and rail mounting system Easy-open cable latches Easy to install Notes: Fits models with bed length 6'10" / 208,28 cm ONLY
Kit Demi-lames Additionnelles IRONMAN 4X4 Load Plus LP4 +450kg • 70x12x442mm • Système breveté qui permet de rouler jusu'à la charge maximum autorisée en toute sécurité • S'installe et se dépose en 20 minutes seulement à l'aide de 2 clés plates • Idéal pour les configurations charges lourdes occasionnelles ou permanentes
Kit Demi-lames Additionnelles IRONMAN 4X4 Load Plus LP7 +450kg • 75x12x438mm • Système breveté qui permet de rouler jusu'à la charge maximum autorisée en toute sécurité • S'installe et se dépose en 20 minutes seulement à l'aide de 2 clés plates • Idéal pour les configurations charges lourdes occasionnelles ou permanentes
Easy to install! Durable, steel construction Includes (2) Rough Country LED Cubes Integrated steps for easy access to bed Retains factory receiver hitch Includes backup sensor relocators Flush LED light specs: 2880 lumens 36 watts Flood beam Each light contains 6, 3 watt high intensity Cree LEDs IP67 Waterproof rating Moisture Breather technology reduces moisture build-up behind the lens Includes premium, flat-wound wiring harness with on/off switch Durable die cast aluminum housing Notes: LEDs are for off-road use ONLY
ROUGH COUNTRY RC10787 • Pare-choc avant acier ROUGH COUNTRY 10787
Durable powder coated steel brackets Push to connect air fittings Internal bump stop in air bag Double convoluted air bag Complete kit Levels truck when towing for safer load carrying In the box: (2) Air bag Mounting brackets U-Bolt plates 90° fittings Inflation valves Hardware Notes: Requires 3-6" lift to be installed Fits models with stock rear blocks ONLY Does NOT increase towing capacity Does NOT fit cab and chassis models Does NOT fit dually models Minor drilling required
Body: 2.5" smooth bore zinc plated seamless steel body Body Plating: Zinc-plated and double-clear coated for long lasting finish Reservoir: 2.5" Smooth bore and honed seamless alloy reservoir Components: Black-anodized, CNC-machined 6061-T6 billet aluminum Shaft: 7/8" hard chrome plated heat-treated alloy steel Piston: Race-developed high-flow piston design Valving: Application specific valving to maximize performance Seals: Redundant sealing pack system main seal, wiper seal, scraper seal Bearing: PTFE-lined, heat-treated, alloy steel spherical Dimensions: Extended: 32.31" Compressed: 19.85" Travel: 12.46" Mounts: Top mount: eyelet Bottom mount: eyelet Notes: Fits 4WD models ONLY
Body 2.5" smooth bore zinc plated seamless steel body Body Plating Zinc-plated and double-clear coated for long lasting finish Reservoir 2.5" Smooth bore and honed seamless alloy reservoir Components Black-anodized, CNC-machined 6061-T6 billet aluminum Shaft 7/8" hard chrome plated heat-treated alloy steel Piston Race-developed high-flow piston design Valving Application specific valving to maximize performance Seals Redundant sealing pack system main seal, wiper seal, scraper seal Bearing PTFE-lined, heat-treated, alloy steel spherical Adjuster Type DSC - Dual Speed Compression Dimensions: Extended: 29.81" Compressed: 18.45" Travel: 11.36" Mounts: Top mount: eyelet Bottom mount: eyelet
Body 2.5" smooth bore zinc plated seamless steel body Body Plating Zinc-plated and double-clear coated for long lasting finish Reservoir 2.5" Smooth bore and honed seamless alloy reservoir Components Black-anodized, CNC-machined 6061-T6 billet aluminum Shaft 7/8" hard chrome plated heat-treated alloy steel Piston Race-developed high-flow piston design Valving Application specific valving to maximize performance Seals Redundant sealing pack system main seal, wiper seal, scraper seal Bearing PTFE-lined, heat-treated, alloy steel spherical Adjuster Type DSC - Dual Speed Compression Dimensions: Extended: 32.31" Compressed: 19.85" Travel: 12.46" Mounts: Top mount: eyelet Bottom mount: eyelet
Body 2.5" smooth bore zinc plated seamless steel body Body Plating Zinc-plated and double-clear coated for long lasting finish Reservoir 2.5" Smooth bore and honed seamless alloy reservoir Components Black-anodized, CNC-machined 6061-T6 billet aluminum Shaft 7/8" hard chrome plated heat-treated alloy steel Piston Race-developed high-flow piston design Valving Application specific valving to maximize performance Seals Redundant sealing pack system main seal, wiper seal, scraper seal Bearing PTFE-lined, heat-treated, alloy steel spherical Adjuster Type DSC - Dual Speed Compression Dimensions: Extended: 35.01" Compressed: 21.45" Travel: 13.56" Mounts: Top mount: eyelet Bottom mount: eyelet
2.0” Impact extruded and CNC machined 6061-T6 clear anodized aluminum one-piece body resists rust over time Clear-anodized for a durable finish Internal IFP mono-tube reservoir design Black-anodized, CNC-machined 6061-T6 billet aluminum Shaft: 5/8" hard chrome plated heat-treated alloy steel Race-developed high-flow piston design Application specific valving to maximize performance Redundant sealing pack system main seal, wiper seal, scraper seal JM92 Advanced Suspension Fluid for improved performance at variable temperatures Quiet nitrile rubber allows for increased suspension articulation Dimensions: Extended: 30.11" Compressed: 18.50" Travel: 11.61" Mounts: Top mount: eyelet Bottom mount: eyelet Notes: Fits 4WD models ONLY Does NOT fits F-350 Super Duty Cab & Chassis models
2.0” Impact extruded and CNC machined 6061-T6 clear anodized aluminum one-piece body resists rust over time Clear-anodized for a durable finish Internal IFP mono-tube reservoir design Black-anodized, CNC-machined 6061-T6 billet aluminum Shaft: 5/8" hard chrome plated heat-treated alloy steel Race-developed high-flow piston design Application specific valving to maximize performance Redundant sealing pack system main seal, wiper seal, scraper seal JM92 Advanced Suspension Fluid for improved performance at variable temperatures Quiet nitrile rubber allows for increased suspension articulation Dimensions: Extended: 32.82" Compressed: 20.20" Travel: 12.62" Mounts: Top mount: eyelet Bottom mount: eyelet Notes: Fits 4WD models ONLY Does NOT fits F-350 Super Duty Cab & Chassis 4WD models
2.0” Impact extruded and CNC machined 6061-T6 clear anodized aluminum one-piece body resists rust over time Clear-anodized for a durable finish Internal IFP mono-tube reservoir design Black-anodized, CNC-machined 6061-T6 billet aluminum Shaft: 5/8" hard chrome plated heat-treated alloy steel Race-developed high-flow piston design Application specific valving to maximize performance Redundant sealing pack system main seal, wiper seal, scraper seal JM92 Advanced Suspension Fluid for improved performance at variable temperatures Quiet nitrile rubber allows for increased suspension articulation Dimensions: Extended: 35.02" Compressed: 21.40" Travel: 13.62" Mounts: Top mount: eyelet Bottom mount: eyelet
2.0" Impact extruded 6061-T6 aluminum will resist rust over time Clear-anodized for a durable finish 2.0" Smooth bore 6061-T6 Aluminum is hard anodized Black-anodized, CNC-machined 6061-T6 billet aluminum Shaft: 5/8" hard chrome plated heat-treated alloy steel Race-developed high-flow piston design Application specific valving to maximize performance JM92 Advanced Suspension Fluid for improved performance at variable temperatures Dimensions: Extended 33.52" Compressed: 19.90" Travel: 13.62" Mounts: Top mount: eyelet Bottom mount: eyelet Notes: Fits 4WD models ONLY Includes billet bracket clamp
2.0" Impact extruded 6061-T6 aluminum will resist rust over time Clear-anodized for a durable finish 2.0" Smooth bore 6061-T6 Aluminum is hard anodized Black-anodized, CNC-machined 6061-T6 billet aluminum Shaft: 5/8" hard chrome plated heat-treated alloy steel Race-developed high-flow piston design Application specific valving to maximize performance JM92 Advanced Suspension Fluid for improved performance at variable temperatures Dimensions: Extended 35.02" Compressed: 20.90" Travel: 14.12" Mounts: Top mount: eyelet Bottom mount: eyelet Notes: Fits 4WD models ONLY Includes billet bracket clamp
DSC - Dual Speed Compression Body: 2.5” Impact extruded and CNC machined 6061-T6 clear anodized aluminum one-piece body resists rust over time Reservoir: 2,5" Smooth bore and honed seamless alloy reservoir Body Plating: Zinc-plated and double-clear coated for long lasting finish Components: Black-anodized, CNC-machined 6061-T6 billet aluminum Shaft: 7/8" hard chrome plated heat-treated alloy steel Piston: Race-developed high-flow piston design Seals: Redundant sealing pack system main seal, wiper seal, and scraper seal Oil: JM92 Advanced Suspension Fluid for improved performance at variable temperatures Adjuster: DSC allows 10 separate low-speed and 12 high-speed compression levels Dimensions: Extended: 29.83" Compressed: 18.35" Travel: 11.48" Mounts: Top mount: eyelet Bottom mount: eyelet
DSC - Dual Speed Compression Body: 2.5” Impact extruded and CNC machined 6061-T6 clear anodized aluminum one-piece body resists rust over time Reservoir: 2,5" Smooth bore and honed seamless alloy reservoir Body Plating: Zinc-plated and double-clear coated for long lasting finish Components: Black-anodized, CNC-machined 6061-T6 billet aluminum Shaft: 7/8" hard chrome plated heat-treated alloy steel Piston: Race-developed high-flow piston design Seals: Redundant sealing pack system main seal, wiper seal, and scraper seal Oil: JM92 Advanced Suspension Fluid for improved performance at variable temperatures Adjuster: DSC allows 10 separate low-speed and 12 high-speed compression levels Dimensions: Extended: 32.33" Compressed: 19.85" Travel: 12.48" Mounts: Top mount: eyelet Bottom mount: eyelet
DSC - Dual Speed Compression Body: 2.5” Impact extruded and CNC machined 6061-T6 clear anodized aluminum one-piece body resists rust over time Reservoir: 2,5" Smooth bore and honed seamless alloy reservoir Body Plating: Zinc-plated and double-clear coated for long lasting finish Components: Black-anodized, CNC-machined 6061-T6 billet aluminum Shaft: 7/8" hard chrome plated heat-treated alloy steel Piston: Race-developed high-flow piston design Seals: Redundant sealing pack system main seal, wiper seal, and scraper seal Oil: JM92 Advanced Suspension Fluid for improved performance at variable temperatures Adjuster: DSC allows 10 separate low-speed and 12 high-speed compression levels Dimensions: Extended: 34.93" Compressed: 21.35" Travel: 13.58" Mounts: Top mount: eyelet Bottom mount: eyelet
2.0" Impact extruded 6061-T6 aluminum will resist rust over time Clear-anodized for a durable finish 2.0" Smooth bore 6061-T6 Aluminum is hard anodized Black-anodized, CNC-machined 6061-T6 billet aluminum Shaft: 5/8" hard chrome plated heat-treated alloy steel Race-developed high-flow piston design Application specific valving to maximize performance JM92 Advanced Suspension Fluid for improved performance at variable temperatures LSC - Low Speed Compression Dimensions: Travel: 30.02" Compressed: 17.90" Extended: 12.12" Mounts: Top mount: eyelet Bottom mount: eyelet Notes: Includes billet reservoir clamp
Made from galvanized steel Solid one piece design Provide easy access to your car especially to the cars with lifted suspension Protective Bedliner black coating: corrosion, impact and abrasion resistance Easy installation, no drilling required 7,5" wide stepping area High-quality product In the box: (2) Side steps Hardware Notes: Additional drop steps GR69420000T available (sold separately) Fits SuperCrew Cab models ONLY
Convenient, roll-up design Easily removeable for 100% bed access High-quality, durable leather grain fabric Designed to withstand the elements Tight front and rear seals keep your bed clean and dry Single trigger latch for easy removal Easy installation Sleek and stylish Notes: Fits 6'10" (208,28 cm) bed models ONLY
Resets your speedometer to accurate readings for larger tyres Easy plug and play connection Updates OE ECM shift points to accommodate larger tyres Recalibrates electronic stability control to work with larger tyres Option to return to stock settings In the box: Speedometer recalibrator USB update cable Notes: Does not work on 2022+ F-150 models equipped with a front facing camera Download the latest software update here One set can be used with one car only, then it's blocked for any other
Body: 2,0” impact extruded and CNC machined 6061-T6 clear anodized aluminum body resists rust over time Body: Plating Hard-anodized for a durable finish Reservoir: External reservoir design separates shock oil from the high-pressure nitrogen Components: Black-anodized, CNC-machined 6061-T6 billet aluminum Shaft: 5/8" hard chrome plated heat-treated alloy steel Piston:Race-developed high-flow piston design Seals: Redundant sealing pack system main seal, wiper seal, scraper seal Oil: JM92 Advanced Suspension Fluid for improved performance at variable temperatures Bushings: Quiet nitrile rubber allows for increased suspension articulation Adjustments: Adjuster - 24 clicks of adjustability Adjusting screw for resistance and damping of the steering system Dimensions: Extended: 22.19" Compressed: 14.09" Travel: 8.11" Mounts: Top mount: tie rod clamp Bottom mount: eyelet Notes: Fits 4WD models ONLY
Body: 2,0” impact extruded and CNC machined 6061-T6 clear anodized aluminum body resists rust over time Body: Plating Hard-anodized for a durable finish Reservoir: External reservoir design separates shock oil from the high-pressure nitrogen Components: Black-anodized, CNC-machined 6061-T6 billet aluminum Shaft: 5/8" hard chrome plated heat-treated alloy steel Piston:Race-developed high-flow piston design Seals: Redundant sealing pack system main seal, wiper seal, scraper seal Oil: JM92 Advanced Suspension Fluid for improved performance at variable temperatures Bushings: Quiet nitrile rubber allows for increased suspension articulation Adjustments: Adjuster - 24 clicks of adjustability Adjusting screw for resistance and damping of the steering system Dimensions: Extended: 24.78" Compressed: 16.67" Travel: 8.11" Mounts: Top mount: tie rod clamp Bottom mount: eyelet Notes: Fits 4WD models ONLY
Body: 2,0” impact extruded and CNC machined 6061-T6 clear anodized aluminum body resists rust over time Body: Clear-anodized for a durable finish Components: Black-anodized, CNC-machined 6061-T6 billet aluminum Shaft: 5/8" hard chrome plated heat-treated alloy steel Piston:Race-developed high-flow piston design Seals: Redundant sealing pack system main seal, wiper seal, scraper seal Oil: JM92 Advanced Suspension Fluid for improved performance at variable temperatures Bushings: Quiet nitrile rubber allows for increased suspension articulation Mounting: Direct replacement for stock and aftermarket lifts kits Dimensions: Extended: 23.17" Compressed: 15.08" Travel: 8.10" Mounts: Top mount: tie rod clamp Bottom mount: eyelet Notes: Fits 4WD models ONLY